[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;lot=20260615;uid=D5B388 [mcu] comment: First Batch C235 220V [mcu SmartPiOne] version: 4cc47cf5 (host SmartPi One)

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 200mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=202.0... Probing with pressure switch... probe at 31.003,202.004 is z=217.237500 probe at 31.003,202.004 is z=175.660000 Tap drift (diff=41.5775mm) — reset probe at 31.003,202.004 is z=175.892500 Tap drift (diff=0.2325mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 31.003,202.004 is z=175.895000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=175.8950 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 202.0) ~ point de tap (31.0, 202.0) Z calibration complete!

Moving to tap point X=31.0 Y=202.0... Probing with pressure switch... probe at 30.994,202.004 is z=265.785000 probe at 30.994,202.004 is z=8.805000 Tap drift (diff=256.9800mm) — reset probe at 30.994,202.004 is z=0.837500 Tap drift (diff=7.9675mm) — reset probe at 30.994,202.004 is z=0.880000 Tap drift (diff=0.0425mm) — reset probe at 30.994,202.004 is z=0.870000 Tap OK (diff=0.0100mm, stable 2/5) Tap drift (diff=0.0100mm) — reset probe at 30.994,202.004 is z=0.882500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,202.004 is z=0.885000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.8850 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 202.0) ~ point de tap (31.0, 202.0) Z calibration complete! probe at 30.994,202.004 is z=255.915000 probe at 30.994,202.004 is z=255.950000 Tap drift (diff=0.0350mm) — reset probe at 30.994,202.004 is z=255.947500 Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=255.9475 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,202.004 is z=255.867500 probe at 30.994,202.004 is z=255.900000 Tap drift (diff=0.0325mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,202.004 is z=255.897500 Tap OK (diff=0.0025mm, stable 3/5) VALIDATED: trigger_z=255.8975 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,202.004 is z=255.902500 VALIDATED: trigger_z=255.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,202.004 is z=255.870000 probe at 30.994,202.004 is z=255.872500 Tap drift (diff=0.0300mm) — reset Tap OK (diff=0.0025mm, stable 5/5)

probe: at 32.495,205.497 bed will contact at z=0.772500 probe: at 32.495,205.497 bed will contact at z=1.040000 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.052500 probe: at 32.495,205.497 bed will contact at z=1.042500 probe: at 32.495,205.497 bed will contact at z=1.050000 probe: at 206.996,205.497 bed will contact at z=1.147500 probe: at 206.996,205.497 bed will contact at z=1.172500 probe: at 206.996,205.497 bed will contact at z=1.175000 probe: at 206.996,31.995 bed will contact at z=-1.410000 probe: at 206.996,31.995 bed will contact at z=-1.320000 probe: at 206.996,31.995 bed will contact at z=-1.362500 probe: at 206.996,31.995 bed will contact at z=-1.432500 probe: at 206.996,31.995 bed will contact at z=-1.380000 probe: at 206.996,31.995 bed will contact at z=-1.355000 probe: at 206.996,31.995 bed will contact at z=-1.315000 probe: at 206.996,31.995 bed will contact at z=-1.357500 probe: at 206.996,31.995 bed will contact at z=-1.335000 probe: at 206.996,31.995 bed will contact at z=-1.287500 probe: at 206.996,31.995 bed will contact at z=-1.330000 probe: at 206.996,31.995 bed will contact at z=-1.312500 probe: at 32.495,31.995 bed will contact at z=-1.202500 probe: at 32.495,31.995 bed will contact at z=-1.230000 probe: at 32.495,31.995 bed will contact at z=-1.232500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.05000 front right screw : x=224.0, y=175.5, z=1.17250 : adjust CW 00:15 rear right screw : x=224.0, y=2.0, z=-1.33000 : adjust CCW 04:46 rear left screw : x=49.5, y=2.0, z=-1.23000 : adjust CCW 04:34