[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=0B0051000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.587500 probe at 65.996,275.995 is z=398.190000 Tap rejete (vibration chassis, z=398.1900 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.996,275.995 is z=296.470000 probe at 65.996,275.995 is z=296.482500 Tap drift (diff=0.0125mm) — reset probe at 65.996,275.995 is z=296.477500 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=298.855000 Tap drift (diff=2.3775mm) — reset probe at 65.996,275.995 is z=296.475000 Tap drift (diff=2.3800mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=296.480000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=296.4800 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.745000 probe at 65.999,275.995 is z=398.475000 Tap rejete (vibration chassis, z=398.4750 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=257.672500 probe at 65.999,275.995 is z=151.585000 Tap drift (diff=106.0875mm) — reset probe at 65.999,275.995 is z=154.065000 Tap drift (diff=2.4800mm) — reset probe at 65.999,275.995 is z=156.550000 Tap drift (diff=2.4850mm) — reset probe at 65.999,275.995 is z=159.002500 Tap drift (diff=2.4525mm) — reset probe at 65.999,275.995 is z=161.480000 Tap drift (diff=2.4775mm) — reset probe at 65.999,275.995 is z=163.965000 probe at 65.999,275.995 is z=166.450000 probe at 65.999,275.995 is z=165.672500 Tap drift (diff=0.7775mm) — reset probe at 65.999,275.995 is z=168.155000 Tap drift (diff=2.4825mm) — reset probe at 65.999,275.995 is z=170.750000 Tap drift (diff=2.5950mm) — reset probe at 65.999,275.995 is z=173.747500 Tap drift (diff=2.9975mm) — reset probe at 65.999,275.995 is z=176.187500 Tap drift (diff=2.4400mm) — reset probe at 65.999,275.995 is z=178.647500 Tap drift (diff=2.4600mm) — reset probe at 65.999,275.995 is z=181.112500 Tap drift (diff=2.4650mm) — reset probe at 65.999,275.995 is z=0.845000 Tap drift (diff=180.2675mm) — reset probe at 65.999,275.995 is z=0.855000 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.862500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=0.865000 Tap OK (diff=0.0025mm, stable 3/5)

probe: at 67.000,271.004 bed will contact at z=2.420000 probe: at 67.000,271.004 bed will contact at z=2.437500 probe: at 67.000,271.004 bed will contact at z=2.430000 probe: at 267.996,271.004 bed will contact at z=2.460000 probe: at 267.996,271.004 bed will contact at z=2.477500 probe: at 267.996,271.004 bed will contact at z=2.472500 probe: at 267.996,71.995 bed will contact at z=2.490000 probe: at 267.996,71.995 bed will contact at z=2.500000 probe: at 67.000,71.995 bed will contact at z=2.457500 probe: at 67.000,71.995 bed will contact at z=2.482500 probe: at 67.000,71.995 bed will contact at z=2.462500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.43000 front right screw : x=285.0, y=241.0, z=2.47250 : adjust CW 00:05 rear right screw : x=285.0, y=42.0, z=2.50000 : adjust CW 00:08 rear left screw : x=84.0, y=42.0, z=2.46250 : adjust CW 00:04