[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=0B0052000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.0334 gap=1.9666 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-18.1919 gap=1.8081 (1/4) tap 3: pos=-18.5819 gap=1.4181 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-18.1919 gap=1.8081 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.2406 spread=0.5850mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-18.1797 gap=1.8203 (1/4) tap 3: pos=-17.8141 gap=2.1859 (2/4) tap 4: pos=-18.1919 gap=1.8081 (3/4) tap 5: pos=-17.9847 gap=2.0153 fenetre=0.3778/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.0426 spread=0.3778mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=413.522500 probe at 49.995,339.999 is z=413.520000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=413.527500 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=413.5275 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=474.312500 probe at 49.998,339.999 is z=400.730000 Tap drift (diff=73.5825mm) — reset probe at 49.998,339.999 is z=402.695000 Tap drift (diff=1.9650mm) — reset probe at 49.998,339.999 is z=405.422500 Tap drift (diff=2.7275mm) — reset probe at 49.998,339.999 is z=339.277500 Tap drift (diff=66.1450mm) — reset probe at 49.998,339.999 is z=342.055000 Tap drift (diff=2.7775mm) — reset probe at 49.998,339.999 is z=344.825000 Tap drift (diff=2.7700mm) — reset probe at 49.998,339.999 is z=347.605000 Tap drift (diff=2.7800mm) — reset probe at 49.998,339.999 is z=350.380000 Tap drift (diff=2.7750mm) — reset probe at 49.998,339.999 is z=326.517500 Tap drift (diff=23.8625mm) — reset probe at 49.998,339.999 is z=329.287500 probe at 49.998,339.999 is z=328.535000 Tap drift (diff=0.7525mm) — reset probe at 49.998,339.999 is z=246.992500 Tap drift (diff=81.5425mm) — reset probe at 49.998,339.999 is z=89.585000 Tap drift (diff=157.4075mm) — reset probe at 49.998,339.999 is z=92.360000 probe at 49.998,339.999 is z=17.405000 Tap drift (diff=74.9550mm) — reset probe at 49.998,339.999 is z=12.837500 Tap drift (diff=4.5675mm) — reset probe at 49.998,339.999 is z=15.325000 Tap drift (diff=2.4875mm) — reset probe at 49.998,339.999 is z=18.090000 Tap drift (diff=2.7650mm) — reset probe at 49.998,339.999 is z=18.277500 Tap drift (diff=0.1875mm) — reset probe at 49.998,339.999 is z=20.757500

probe: at 54.997,328.001 bed will contact at z=1.952500 probe: at 54.997,328.001 bed will contact at z=1.950000 probe: at 380.001,328.001 bed will contact at z=1.932500 probe: at 380.001,328.001 bed will contact at z=1.922500 probe: at 380.001,328.001 bed will contact at z=1.942500 probe: at 380.001,101.996 bed will contact at z=1.990000 probe: at 380.001,101.996 bed will contact at z=2.015000 probe: at 54.997,101.996 bed will contact at z=1.895000 probe: at 54.997,101.996 bed will contact at z=1.905000 probe: at 54.997,101.996 bed will contact at z=1.897500 probe: at 217.505,214.498 bed will contact at z=2.090000 probe: at 217.505,214.498 bed will contact at z=2.085000 probe: at 217.505,214.498 bed will contact at z=2.070000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.95250 front right screw : x=397.0, y=298.0, z=1.93250 : adjust CCW 00:02 rear right screw : x=397.0, y=72.0, z=1.99000 : adjust CW 00:05 rear left screw : x=72.0, y=72.0, z=1.89750 : adjust CCW 00:07 middle : x=234.5, y=184.5, z=2.08500 : adjust CW 00:16