[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=100041000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-18.1797 gap=1.8203 (1/4) tap 3: pos=-18.7891 gap=1.2109 (2/4) tap 4: pos=-18.5819 gap=1.4181 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.7922/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.3869 spread=0.7922mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2041 gap=1.7959 (chauffe, ignore) tap 2: pos=457.1919 gap=1.8081 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=409.487500 probe at 49.995,339.999 is z=409.495000 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,339.999 is z=409.497500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.995,339.999 is z=409.500000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=409.5000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=462.665000 probe at 49.998,339.999 is z=455.617500 Tap drift (diff=7.0475mm) — reset probe at 49.998,339.999 is z=447.577500 Tap drift (diff=8.0400mm) — reset probe at 49.998,339.999 is z=439.850000 Tap drift (diff=7.7275mm) — reset probe at 49.998,339.999 is z=431.722500 Tap drift (diff=8.1275mm) — reset probe at 49.998,339.999 is z=432.890000 Tap drift (diff=1.1675mm) — reset probe at 49.998,339.999 is z=123.805000 Tap drift (diff=309.0850mm) — reset probe at 49.998,339.999 is z=25.012500 Tap drift (diff=98.7925mm) — reset probe at 49.998,339.999 is z=14.372500 Tap drift (diff=10.6400mm) — reset probe at 49.998,339.999 is z=7.222500 Tap drift (diff=7.1500mm) — reset probe at 49.998,339.999 is z=1.000000 Tap drift (diff=6.2225mm) — reset probe at 49.998,339.999 is z=0.995000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,339.999 is z=0.997500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=1.017500 Tap drift (diff=0.0225mm) — reset probe at 49.998,339.999 is z=2.187500 Tap drift (diff=1.1700mm) — reset Tap drift (diff=1.1875mm) — reset probe at 49.998,339.999 is z=1.012500 Tap drift (diff=0.0125mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=1.010000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0075mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5)

probe: at 54.997,328.001 bed will contact at z=1.190000 probe: at 54.997,328.001 bed will contact at z=1.180000 probe: at 54.997,328.001 bed will contact at z=1.187500 probe: at 380.001,328.001 bed will contact at z=1.175000 probe: at 380.001,328.001 bed will contact at z=1.177500 probe: at 380.001,101.996 bed will contact at z=1.237500 probe: at 380.001,101.996 bed will contact at z=1.242500 probe: at 54.997,101.996 bed will contact at z=1.252500 probe: at 217.505,214.498 bed will contact at z=1.235000 probe: at 217.505,214.498 bed will contact at z=1.250000 probe: at 217.505,214.498 bed will contact at z=1.307500 Probe samples exceed tolerance. Retrying... probe: at 217.505,214.498 bed will contact at z=1.255000 probe: at 217.505,214.498 bed will contact at z=1.280000 probe: at 217.505,214.498 bed will contact at z=1.282500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.18750 front right screw : x=397.0, y=298.0, z=1.17500 : adjust CCW 00:01 rear right screw : x=397.0, y=72.0, z=1.23750 : adjust CW 00:06 rear left screw : x=72.0, y=72.0, z=1.25250 : adjust CW 00:08 middle : x=234.5, y=184.5, z=1.28000 : adjust CW 00:11