[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=10005D000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) tap 2 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) YUMI_SENSORLESS_HOME Y: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3 rejete: cible atteinte sans buter (gap=0.0531) tap 4 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) YUMI_SENSORLESS_HOME Y: home de base suspect (pas de contact) -> re-home de recuperation 2/2 tap 5: pos=-18.6428 gap=1.3572 (chauffe, ignore) tap 6: pos=-17.9969 gap=2.0031 (1/4) tap 7: pos=-17.9969 gap=2.0031 (2/4) tap 8: pos=-17.9969 gap=2.0031 (3/4) tap 9: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (4 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: cible atteinte sans buter (gap=0.4431) tap 2: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 3: pos=-17.9969 gap=2.0031 (1/4) tap 4: pos=-17.9969 gap=2.0031 (2/4) tap 5: pos=-17.9969 gap=2.0031 (3/4) tap 6: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (1 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: cible atteinte sans buter (gap=0.0531) tap 2: pos=-18.3869 gap=1.6131 (chauffe, ignore) tap 3: pos=-17.9969 gap=2.0031 (1/4) tap 4: pos=-17.9969 gap=2.0031 (2/4) tap 5: pos=-17.9969 gap=2.0031 (3/4) tap 6: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (1 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=386.042500 probe at 49.995,339.999 is z=386.047500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=386.045000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.995,339.999 is z=386.057500 Tap drift (diff=0.0100mm) — reset probe at 49.995,339.999 is z=386.050000 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0075mm, stable 3/5) Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=386.0425 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.400000 probe at 49.998,339.999 is z=497.792500 Tap rejete (vibration chassis, z=497.7925 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,339.999 is z=484.545000 probe at 49.998,339.999 is z=486.907500 Tap drift (diff=2.3625mm) — reset probe at 49.998,339.999 is z=489.310000 Tap drift (diff=2.4025mm) — reset probe at 49.998,339.999 is z=491.675000 Tap drift (diff=2.3650mm) — reset probe at 49.998,339.999 is z=494.032500 Tap drift (diff=2.3575mm) — reset probe at 49.998,339.999 is z=496.427500 Tap drift (diff=2.3950mm) — reset probe at 49.998,339.999 is z=498.835000 Tap rejete (vibration chassis, z=498.8350 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 49.998,339.999 is z=1.115000 probe at 49.998,339.999 is z=1.122500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=1.125000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.998,339.999 is z=1.127500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.1250 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.102500 Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.998,339.999 is z=486.105000 VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.097500 probe at 49.998,339.999 is z=486.100000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000)

probe: at 54.997,328.001 bed will contact at z=1.840000 probe: at 54.997,328.001 bed will contact at z=1.835000 probe: at 380.001,328.001 bed will contact at z=1.790000 probe: at 380.001,328.001 bed will contact at z=1.795000 probe: at 380.001,328.001 bed will contact at z=1.797500 probe: at 380.001,101.996 bed will contact at z=1.657500 probe: at 380.001,101.996 bed will contact at z=1.652500 probe: at 54.997,101.996 bed will contact at z=1.732500 probe: at 54.997,101.996 bed will contact at z=1.722500 probe: at 217.505,214.498 bed will contact at z=1.810000 probe: at 217.505,214.498 bed will contact at z=1.822500 probe: at 217.505,214.498 bed will contact at z=1.835000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.84000 front right screw : x=397.0, y=298.0, z=1.79500 : adjust CCW 00:05 rear right screw : x=397.0, y=72.0, z=1.65750 : adjust CCW 00:22 rear left screw : x=72.0, y=72.0, z=1.72250 : adjust CCW 00:14 middle : x=234.5, y=184.5, z=1.82250 : adjust CCW 00:02