[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=110043000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=256.1797 gap=1.8203 (3/4) tap 5: pos=255.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.1919 gap=1.8081 (3/4) tap 5: pos=-30.5819 gap=1.4181 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5850mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9719 gap=1.0281 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=186.140000 probe at 31.003,211.998 is z=186.165000 Tap drift (diff=0.0250mm) — reset probe at 31.003,211.998 is z=186.172500 Tap OK (diff=0.0075mm, stable 2/5) probe at 31.003,211.998 is z=186.180000 Tap OK (diff=0.0075mm, stable 3/5) probe at 31.003,211.998 is z=186.202500 Tap drift (diff=0.0225mm) — reset probe at 31.003,211.998 is z=186.207500 Tap OK (diff=0.0050mm, stable 2/5) probe at 31.003,211.998 is z=187.077500 Tap drift (diff=0.8700mm) — reset probe at 31.003,211.998 is z=186.215000 Tap drift (diff=0.8625mm) — reset probe at 31.003,211.998 is z=186.220000 probe at 31.003,211.998 is z=186.212500 probe at 31.003,211.998 is z=186.217500 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=186.2125 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=17.507500 probe at 30.994,211.998 is z=17.540000 Tap drift (diff=0.0325mm) — reset probe at 30.994,211.998 is z=17.547500 Tap OK (diff=0.0075mm, stable 2/5) probe at 30.994,211.998 is z=17.552500 Tap OK (diff=0.0050mm, stable 3/5) probe at 30.994,211.998 is z=17.575000 Tap drift (diff=0.0225mm) — reset probe at 30.994,211.998 is z=17.582500 probe at 30.994,211.998 is z=17.587500 probe at 30.994,211.998 is z=17.590000 Tap OK (diff=0.0025mm, stable 4/5) probe at 30.994,211.998 is z=17.610000 Tap drift (diff=0.0200mm) — reset probe at 30.994,211.998 is z=17.617500 probe at 30.994,211.998 is z=17.620000 Tap OK (diff=0.0025mm, stable 3/5) probe at 30.994,211.998 is z=17.627500 Tap OK (diff=0.0075mm, stable 4/5) probe at 30.994,211.998 is z=17.652500 Tap drift (diff=0.0250mm) — reset probe at 30.994,211.998 is z=17.632500 Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=17.657500 probe at 30.994,211.998 is z=17.660000 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=17.665000 probe at 30.994,211.998 is z=17.667500 probe at 30.994,211.998 is z=17.670000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=17.6700 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=255.920000 probe at 30.994,211.998 is z=255.927500 probe at 30.994,211.998 is z=255.932500 probe at 30.994,211.998 is z=255.940000

probe: at 32.495,205.497 bed will contact at z=0.552500 probe: at 32.495,205.497 bed will contact at z=0.545000 probe: at 32.495,205.497 bed will contact at z=0.555000 probe: at 206.996,205.497 bed will contact at z=0.742500 probe: at 206.996,205.497 bed will contact at z=0.747500 probe: at 206.996,31.995 bed will contact at z=1.122500 probe: at 206.996,31.995 bed will contact at z=1.140000 probe: at 206.996,31.995 bed will contact at z=1.152500 probe: at 32.495,31.995 bed will contact at z=1.410000 probe: at 32.495,31.995 bed will contact at z=1.415000 probe: at 32.495,31.995 bed will contact at z=1.412500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=0.55250 front right screw : x=224.0, y=175.5, z=0.74250 : adjust CW 00:23 rear right screw : x=224.0, y=2.0, z=1.14000 : adjust CW 01:11 rear left screw : x=49.5, y=2.0, z=1.41250 : adjust CW 01:43