[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=120041000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.8012 gap=1.1988 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2041 gap=1.7959 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.3991 gap=1.6009 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.4874 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,340.003 is z=414.952500 probe at 49.995,340.003 is z=414.962500 Tap drift (diff=0.0100mm) — reset probe at 49.995,340.003 is z=414.955000 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0075mm, stable 3/5) probe at 49.995,340.003 is z=414.965000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=414.9650 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,340.003 is z=492.292500 probe at 49.998,340.003 is z=481.457500 Tap drift (diff=10.8350mm) — reset probe at 49.998,340.003 is z=483.737500 Tap drift (diff=2.2800mm) — reset probe at 49.998,340.003 is z=484.412500 Tap drift (diff=0.6750mm) — reset probe at 49.998,340.003 is z=474.897500 Tap drift (diff=9.5150mm) — reset probe at 49.998,340.003 is z=467.745000 Tap drift (diff=7.1525mm) — reset probe at 49.998,340.003 is z=460.767500 Tap drift (diff=6.9775mm) — reset probe at 49.998,340.003 is z=461.705000 Tap drift (diff=0.9375mm) — reset probe at 49.998,340.003 is z=440.495000 Tap drift (diff=21.2100mm) — reset probe at 49.998,340.003 is z=430.625000 Tap drift (diff=9.8700mm) — reset probe at 49.998,340.003 is z=393.100000 Tap drift (diff=37.5250mm) — reset probe at 49.998,340.003 is z=85.142500 Tap drift (diff=307.9575mm) — reset probe at 49.998,340.003 is z=1.070000 Tap drift (diff=84.0725mm) — reset probe at 49.998,340.003 is z=1.085000 Tap drift (diff=0.0150mm) — reset probe at 49.998,340.003 is z=1.092500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,340.003 is z=1.095000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,340.003 is z=1.097500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=1.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,340.003 is z=486.100000

probe: at 54.997,315.001 bed will contact at z=1.955000 probe: at 380.001,315.001 bed will contact at z=1.922500 probe: at 380.001,315.001 bed will contact at z=1.932500 probe: at 380.001,315.001 bed will contact at z=1.937500 probe: at 380.001,83.000 bed will contact at z=1.900000 probe: at 380.001,83.000 bed will contact at z=1.920000 probe: at 54.997,83.000 bed will contact at z=1.965000 probe: at 54.997,83.000 bed will contact at z=1.960000 probe: at 217.505,202.498 bed will contact at z=2.012500 probe: at 217.505,202.498 bed will contact at z=1.992500 probe: at 217.505,202.498 bed will contact at z=2.072500 Probe samples exceed tolerance. Retrying... probe: at 217.505,202.498 bed will contact at z=2.085000 probe: at 217.505,202.498 bed will contact at z=2.025000 probe: at 217.505,202.498 bed will contact at z=2.027500 probe: at 217.505,202.498 bed will contact at z=2.000000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=285.0, z=1.95500 front right screw : x=397.0, y=285.0, z=1.93250 : adjust CCW 00:03 rear right screw : x=397.0, y=53.0, z=1.92000 : adjust CCW 00:04 rear left screw : x=72.0, y=53.0, z=1.96500 : adjust CW 00:01 rear left screw : x=234.5, y=172.5, z=2.00000 : adjust CW 00:05