[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=120044000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=357.1919 gap=1.8081 (1/4) tap 3: pos=356.8019 gap=2.1981 (2/4) tap 4: pos=357.1919 gap=1.8081 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0456 spread=0.3900mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=357.1919 gap=1.8081 (1/4) tap 3: pos=356.8019 gap=2.1981 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-30.5941 gap=1.4059 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.8019 gap=2.1981 (1/4) tap 3: pos=357.1919 gap=1.8081 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-30.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=324.722500 probe at 65.996,275.995 is z=306.255000 Tap drift (diff=18.4675mm) — reset probe at 65.996,275.995 is z=306.262500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=306.272500 Tap drift (diff=0.0100mm) — reset probe at 65.996,275.995 is z=306.260000 Tap drift (diff=0.0125mm) — reset probe at 65.996,275.995 is z=306.257500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=306.267500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=306.2675 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.747500 probe at 65.999,275.995 is z=276.352500 Tap drift (diff=119.3950mm) — reset probe at 65.999,275.995 is z=75.067500 Tap drift (diff=201.2850mm) — reset probe at 65.999,275.995 is z=0.845000 Tap drift (diff=74.2225mm) — reset probe at 65.999,275.995 is z=0.852500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=0.862500 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.860000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.999,275.995 is z=0.857500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.8600 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.892500 probe at 65.999,275.995 is z=385.910000 Tap drift (diff=0.0175mm) — reset probe at 65.999,275.995 is z=385.905000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=385.902500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=385.907500 VALIDATED: trigger_z=385.9075 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=386.147500 probe at 65.999,275.995 is z=385.995000 Tap drift (diff=0.1525mm) — reset probe at 65.999,275.995 is z=385.952500 Tap drift (diff=0.0425mm) — reset probe at 65.999,275.995 is z=385.927500 Tap drift (diff=0.0250mm) — reset probe at 65.999,275.995 is z=385.912500 Tap drift (diff=0.0150mm) — reset

probe: at 67.000,271.004 bed will contact at z=1.017500 probe: at 67.000,271.004 bed will contact at z=1.022500 probe: at 67.000,271.004 bed will contact at z=1.010000 probe: at 267.996,271.004 bed will contact at z=1.127500 probe: at 267.996,271.004 bed will contact at z=1.170000 probe: at 267.996,271.004 bed will contact at z=1.180000 Probe samples exceed tolerance. Retrying... probe: at 267.996,271.004 bed will contact at z=1.137500 probe: at 267.996,271.004 bed will contact at z=1.162500 probe: at 267.996,271.004 bed will contact at z=1.147500 probe: at 267.996,71.995 bed will contact at z=1.042500 probe: at 267.996,71.995 bed will contact at z=1.082500 probe: at 67.000,71.995 bed will contact at z=1.047500 probe: at 67.000,71.995 bed will contact at z=1.045000 probe: at 67.000,71.995 bed will contact at z=1.030000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.01750 front right screw : x=285.0, y=241.0, z=1.14750 : adjust CW 00:16 rear right screw : x=285.0, y=42.0, z=1.04250 : adjust CW 00:03 rear left screw : x=84.0, y=42.0, z=1.04500 : adjust CW 00:03