[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=13005F000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) tap 2 rejete: aucun contact sur 7.0mm (No trigger on probe after full movement) YUMI_SENSORLESS_HOME Y: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3: pos=-18.9719 gap=1.0281 (chauffe, ignore) tap 4: pos=-18.5819 gap=1.4181 (1/4) tap 5: pos=-17.9969 gap=2.0031 (2/4) tap 6: pos=-18.1797 gap=1.8203 (3/4) tap 7: pos=-18.7891 gap=1.2109 fenetre=0.7922/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (2 rejetes) -> moyenne=-18.3869 spread=0.7922mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=457.7769 gap=1.2231 (3/4) tap 5: pos=457.7769 gap=1.2231 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=410.712500 probe at 49.995,339.999 is z=410.715000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,339.999 is z=410.717500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=410.7175 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=324.227500 probe at 49.998,339.999 is z=267.425000 Tap drift (diff=56.8025mm) — reset probe at 49.998,339.999 is z=217.300000 Tap drift (diff=50.1250mm) — reset probe at 49.998,339.999 is z=95.705000 Tap drift (diff=121.5950mm) — reset probe at 49.998,339.999 is z=65.465000 Tap drift (diff=30.2400mm) — reset probe at 49.998,339.999 is z=65.780000 Tap drift (diff=0.3150mm) — reset probe at 49.998,339.999 is z=48.672500 Tap drift (diff=17.1075mm) — reset probe at 49.998,339.999 is z=48.035000 Tap drift (diff=0.6375mm) — reset probe at 49.998,339.999 is z=45.630000 Tap drift (diff=2.4050mm) — reset probe at 49.998,339.999 is z=44.100000 Tap drift (diff=1.5300mm) — reset probe at 49.998,339.999 is z=46.547500 Tap drift (diff=2.4475mm) — reset probe at 49.998,339.999 is z=1.072500 Tap drift (diff=45.4750mm) — reset probe at 49.998,339.999 is z=1.102500 Tap drift (diff=0.0300mm) — reset probe at 49.998,339.999 is z=1.105000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.097500 probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.102500 Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000)

probe: at 54.997,328.001 bed will contact at z=1.050000 probe: at 54.997,328.001 bed will contact at z=1.052500 probe: at 54.997,328.001 bed will contact at z=1.087500 probe: at 380.001,328.001 bed will contact at z=0.952500 probe: at 380.001,328.001 bed will contact at z=0.977500 probe: at 380.001,328.001 bed will contact at z=0.990000 probe: at 380.001,101.996 bed will contact at z=0.930000 probe: at 380.001,101.996 bed will contact at z=0.917500 probe: at 380.001,101.996 bed will contact at z=0.912500 probe: at 54.997,101.996 bed will contact at z=1.142500 probe: at 54.997,101.996 bed will contact at z=1.135000 probe: at 54.997,101.996 bed will contact at z=1.052500 Probe samples exceed tolerance. Retrying... probe: at 54.997,101.996 bed will contact at z=1.085000 probe: at 54.997,101.996 bed will contact at z=1.117500 probe: at 54.997,101.996 bed will contact at z=1.080000 probe: at 217.505,214.498 bed will contact at z=1.020000 probe: at 217.505,214.498 bed will contact at z=1.015000 probe: at 217.505,214.498 bed will contact at z=1.022500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.05250 front right screw : x=397.0, y=298.0, z=0.97750 : adjust CCW 00:09 rear right screw : x=397.0, y=72.0, z=0.91750 : adjust CCW 00:16 rear left screw : x=72.0, y=72.0, z=1.08500 : adjust CW 00:04 middle : x=234.5, y=184.5, z=1.02000 : adjust CCW 00:04