← Home · All machines · All YMS reports → · Packed printers · Trash
SmartPi 1
SmartPi 2

15005D000C51353234323830

PASS Grade A Grade B
Model : C335 · Batch : 20260618
Heated bed : 220V · 500W · SSR SSR10DA
QC pad (MAC) : 0281E38DE8BE
Start : 2026-07-16T03:11:51.974582 · End : 2026-07-16T03:24:05.304977 · Duration : 733 s
Received (server) : 2026-07-17T06:36:43
yumi_config : board=SMART_MAKER_1_X cpu=STM32F401 conn=UART device=C335 x=SMART_TMC2209_V2 y=SMART_TMC2209_V2 z=SMART_TMC2209_V2 e0=SMART_TMC2209_V2 e1=SMART_TMC2209_V2 mx=42BYGH3023-B-22DH my=42BYGH3023-B-22DH mz=42BYGH2216-B-24DH piezo=YN15T-85A1-W100_15-2P pzb=Smart_Z-Offset pzbv=0.2 mains=220V bedw=500 ssr=SSR10DA lot=20260618 uid=36C6E9

Proof photos (packing)

Switch to mobile pipeline mode
TestResultTimeDetails / log
MCU + firmware PASS 03:11:52
[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=15005D000C51353234323830
Home X PASS 03:12:15
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000
Home Y PASS 03:12:48
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000
Motherboard fan PASS 03:13:12
Part fan PASS 03:13:14
Hotend fan PASS 03:13:16
Hotend heat 220°C PASS 03:13:16
Bed heat 60°C PASS 03:13:35
Cutter (feed+cut) PASS 03:15:11
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-30.0091 gap=1.9909 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''
YMS-2 feed to head PASS 03:15:21
Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK
Z tap home + Zmax PASS 03:18:19
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=288.490000 probe at 65.996,275.995 is z=288.492500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.996,275.995 is z=288.507500 Tap drift (diff=0.0150mm) — reset probe at 65.996,275.995 is z=288.512500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.996,275.995 is z=288.520000 Tap OK (diff=0.0075mm, stable 4/5) probe at 65.996,275.995 is z=288.515000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=288.5150 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!
Z tap repeatability PASS 03:23:36 OK: 3 taps convergents spread=0.0000mm (tol=0.0500) sur 15 taps | taps=0.8675, 385.9375, 385.9175, 385.9100, 385.9075, 385.9025, 385.9025, 385.9025, 385.9000, 385.9025, 385.8950, 385.9050, 385.9000, 385.8975, 385.9050
Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=264.657500 probe at 65.999,275.995 is z=122.937500 Tap drift (diff=141.7200mm) — reset probe at 65.999,275.995 is z=13.675000 Tap drift (diff=109.2625mm) — reset probe at 65.999,275.995 is z=15.907500 Tap drift (diff=2.2325mm) — reset probe at 65.999,275.995 is z=0.835000 Tap drift (diff=15.0725mm) — reset probe at 65.999,275.995 is z=0.852500 Tap drift (diff=0.0175mm) — reset probe at 65.999,275.995 is z=0.855000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=0.860000 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.999,275.995 is z=0.867500 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.8675 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.905000 probe at 65.999,275.995 is z=385.922500 probe at 65.999,275.995 is z=385.932500 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=385.930000 probe at 65.999,275.995 is z=385.937500 Tap OK (diff=0.0075mm, stable 3/5) probe at 65.999,275.995 is z=385.940000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=385.9375 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.890000 probe at 65.999,275.995 is z=385.910000 Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=388.792500 Tap drift (diff=2.8825mm) — reset probe at 65.999,275.995 is z=385.902500
Screws tilt PASS 03:24:05
probe: at 67.000,271.004 bed will contact at z=2.482500 probe: at 67.000,271.004 bed will contact at z=2.505000 probe: at 67.000,271.004 bed will contact at z=2.497500 probe: at 267.996,271.004 bed will contact at z=2.480000 probe: at 267.996,271.004 bed will contact at z=2.485000 probe: at 267.996,271.004 bed will contact at z=2.482500 probe: at 267.996,71.995 bed will contact at z=2.525000 probe: at 267.996,71.995 bed will contact at z=2.532500 probe: at 67.000,71.995 bed will contact at z=2.357500 probe: at 67.000,71.995 bed will contact at z=2.362500 probe: at 67.000,71.995 bed will contact at z=2.367500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.49750 front right screw : x=285.0, y=241.0, z=2.48250 : adjust CCW 00:02 rear right screw : x=285.0, y=42.0, z=2.52500 : adjust CW 00:03 rear left screw : x=84.0, y=42.0, z=2.36250 : adjust CCW 00:16