[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=170045000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4234 gap=1.5766 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1797 gap=1.8203 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-18.0091 gap=1.9909 (1/4) tap 3: pos=-17.9847 gap=2.0153 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4234 gap=1.5766 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=457.1797 gap=1.8203 (3/4) tap 5: pos=456.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=415.077500 probe at 49.995,339.999 is z=415.092500 Tap drift (diff=0.0150mm) — reset probe at 49.995,339.999 is z=415.100000 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,339.999 is z=415.102500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=415.105000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=415.1050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.222500 probe at 49.998,339.999 is z=15.365000 Tap drift (diff=479.8575mm) — reset probe at 49.998,339.999 is z=15.440000 Tap drift (diff=0.0750mm) — reset probe at 49.998,339.999 is z=15.445000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,339.999 is z=15.447500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.998,339.999 is z=15.452500 Tap OK (diff=0.0050mm, stable 4/5) probe at 49.998,339.999 is z=15.455000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=15.4550 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=485.907500 probe at 49.998,339.999 is z=485.917500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=485.920000 probe at 49.998,339.999 is z=485.925000 probe at 49.998,339.999 is z=485.935000 probe at 49.998,339.999 is z=485.940000 probe at 49.998,339.999 is z=485.942500 probe at 49.998,339.999 is z=485.947500 probe at 49.998,339.999 is z=485.952500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=485.9525 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.897500 probe at 49.998,339.999 is z=485.905000 Tap OK (diff=0.0075mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=485.910000 VALIDATED: trigger_z=485.9100 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.902500 Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 5/5)

probe: at 54.997,328.001 bed will contact at z=1.370000 probe: at 54.997,328.001 bed will contact at z=1.375000 probe: at 380.001,328.001 bed will contact at z=1.510000 probe: at 380.001,328.001 bed will contact at z=1.525000 probe: at 380.001,101.996 bed will contact at z=1.415000 probe: at 380.001,101.996 bed will contact at z=1.412500 probe: at 54.997,101.996 bed will contact at z=1.415000 probe: at 54.997,101.996 bed will contact at z=1.427500 probe: at 54.997,101.996 bed will contact at z=1.420000 probe: at 217.505,214.498 bed will contact at z=1.530000 probe: at 217.505,214.498 bed will contact at z=1.537500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.37500 front right screw : x=397.0, y=298.0, z=1.51000 : adjust CW 00:16 rear right screw : x=397.0, y=72.0, z=1.41250 : adjust CW 00:05 rear left screw : x=72.0, y=72.0, z=1.42000 : adjust CW 00:05 middle : x=234.5, y=184.5, z=1.53000 : adjust CW 00:19