[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=300;ssr=SSR10DA;lot=20260618;uid=BBA413 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=18003F000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-29.8019 gap=2.1981 (2/4) tap 4: pos=-30.1919 gap=1.8081 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0456 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1919 gap=1.8081 (2/4) tap 4: pos=-29.8019 gap=2.1981 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=151.237500 Tap OK (diff=0.0000mm, stable 2/5) probe at 31.003,211.998 is z=151.240000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=151.2400 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=0.797500 probe at 30.994,211.998 is z=0.840000 Tap drift (diff=0.0425mm) — reset probe at 30.994,211.998 is z=0.847500 Tap OK (diff=0.0075mm, stable 2/5) probe at 30.994,211.998 is z=3.122500 Tap drift (diff=2.2750mm) — reset probe at 30.994,211.998 is z=0.845000 Tap drift (diff=2.2775mm) — reset probe at 30.994,211.998 is z=0.852500 probe at 30.994,211.998 is z=0.862500 Tap drift (diff=0.0100mm) — reset probe at 30.994,211.998 is z=0.867500 Tap OK (diff=0.0050mm, stable 2/5) probe at 30.994,211.998 is z=0.870000 Tap OK (diff=0.0025mm, stable 3/5) probe at 30.994,211.998 is z=0.872500 Tap OK (diff=0.0025mm, stable 4/5) probe at 30.994,211.998 is z=0.875000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.8750 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=256.072500 probe at 30.994,211.998 is z=256.090000 Tap drift (diff=0.0175mm) — reset probe at 30.994,211.998 is z=256.097500 probe at 30.994,211.998 is z=256.100000 probe at 30.994,211.998 is z=256.102500 Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=256.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap drift (diff=0.0250mm) — reset Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=256.105000 probe at 30.994,211.998 is z=256.107500 VALIDATED: trigger_z=256.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 30.994,211.998 is z=256.080000 probe at 30.994,211.998 is z=256.095000

probe: at 32.495,205.497 bed will contact at z=1.625000 probe: at 32.495,205.497 bed will contact at z=1.637500 probe: at 32.495,205.497 bed will contact at z=1.647500 probe: at 206.996,205.497 bed will contact at z=1.245000 probe: at 206.996,205.497 bed will contact at z=1.285000 probe: at 206.996,205.497 bed will contact at z=1.332500 Probe samples exceed tolerance. Retrying... probe: at 206.996,205.497 bed will contact at z=1.322500 probe: at 206.996,205.497 bed will contact at z=1.337500 probe: at 206.996,205.497 bed will contact at z=1.352500 probe: at 206.996,31.995 bed will contact at z=1.450000 probe: at 206.996,31.995 bed will contact at z=1.467500 probe: at 206.996,31.995 bed will contact at z=1.490000 probe: at 32.495,31.995 bed will contact at z=1.577500 probe: at 32.495,31.995 bed will contact at z=1.587500 probe: at 32.495,31.995 bed will contact at z=1.610000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.63750 front right screw : x=224.0, y=175.5, z=1.33750 : adjust CCW 00:36 rear right screw : x=224.0, y=2.0, z=1.46750 : adjust CCW 00:20 rear left screw : x=49.5, y=2.0, z=1.58750 : adjust CCW 00:06