[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=180045000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-30.0091 gap=1.9909 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=357.1797 gap=1.8203 (1/4) tap 3: pos=356.8141 gap=2.1859 (2/4) tap 4: pos=357.1797 gap=1.8203 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0426 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=357.1797 gap=1.8203 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=312.835000 probe at 65.996,275.995 is z=312.842500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=312.845000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.996,275.995 is z=312.847500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=312.8475 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=294.055000 probe at 65.999,275.995 is z=14.940000 Tap drift (diff=279.1150mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=14.942500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.999,275.995 is z=14.957500 Tap drift (diff=0.0150mm) — reset probe at 65.999,275.995 is z=14.960000 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 3/5) probe at 65.999,275.995 is z=14.945000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=14.9450 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.900000 probe at 65.999,275.995 is z=385.917500 probe at 65.999,275.995 is z=385.920000 probe at 65.999,275.995 is z=385.902500 VALIDATED: trigger_z=385.9025 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.915000 Tap OK (diff=0.0050mm, stable 4/5) Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=385.905000 Tap OK (diff=0.0100mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) probe at 65.999,275.995 is z=385.910000 probe at 65.999,275.995 is z=385.912500 Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=385.9125 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) VALIDATED: trigger_z=385.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.897500 Tap OK (diff=0.0050mm, stable 3/5) VALIDATED: trigger_z=385.8975 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

probe: at 67.000,271.004 bed will contact at z=2.890000 probe: at 67.000,271.004 bed will contact at z=2.887500 probe: at 267.996,271.004 bed will contact at z=3.012500 probe: at 267.996,271.004 bed will contact at z=3.027500 probe: at 267.996,271.004 bed will contact at z=3.100000 Probe samples exceed tolerance. Retrying... probe: at 267.996,271.004 bed will contact at z=2.892500 probe: at 267.996,271.004 bed will contact at z=2.930000 probe: at 267.996,271.004 bed will contact at z=3.120000 probe: at 267.996,271.004 bed will contact at z=3.197500 probe: at 267.996,271.004 bed will contact at z=3.140000 probe: at 267.996,271.004 bed will contact at z=3.107500 probe: at 267.996,271.004 bed will contact at z=2.947500 probe: at 267.996,271.004 bed will contact at z=2.900000 probe: at 267.996,271.004 bed will contact at z=3.017500 probe: at 267.996,271.004 bed will contact at z=3.147500 probe: at 267.996,271.004 bed will contact at z=2.922500 probe: at 267.996,271.004 bed will contact at z=2.997500 probe: at 267.996,271.004 bed will contact at z=3.007500 probe: at 267.996,271.004 bed will contact at z=3.015000 probe: at 267.996,71.995 bed will contact at z=2.927500 probe: at 267.996,71.995 bed will contact at z=2.907500 probe: at 267.996,71.995 bed will contact at z=3.002500 probe: at 267.996,71.995 bed will contact at z=2.812500 probe: at 267.996,71.995 bed will contact at z=3.015000 probe: at 267.996,71.995 bed will contact at z=3.005000 probe: at 267.996,71.995 bed will contact at z=2.895000 probe: at 267.996,71.995 bed will contact at z=2.945000 probe: at 267.996,71.995 bed will contact at z=2.972500 probe: at 267.996,71.995 bed will contact at z=2.860000 probe: at 267.996,71.995 bed will contact at z=3.000000 probe: at 267.996,71.995 bed will contact at z=2.980000 probe: at 267.996,71.995 bed will contact at z=2.935000 probe: at 267.996,71.995 bed will contact at z=2.977500 probe: at 267.996,71.995 bed will contact at z=2.865000 probe: at 267.996,71.995 bed will contact at z=3.042500 probe: at 267.996,71.995 bed will contact at z=2.957500 probe: at 267.996,71.995 bed will contact at z=2.985000 probe: at 267.996,71.995 bed will contact at z=2.987500 probe: at 67.000,71.995 bed will contact at z=2.895000