[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=19005F000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.8141 gap=2.1859 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9512 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=457.5941 gap=1.4059 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=402.252500 probe at 49.995,339.999 is z=401.880000 Tap drift (diff=0.3725mm) — reset probe at 49.995,339.999 is z=400.882500 Tap drift (diff=0.9975mm) — reset probe at 49.995,339.999 is z=400.020000 Tap drift (diff=0.8625mm) — reset probe at 49.995,339.999 is z=399.300000 Tap drift (diff=0.7200mm) — reset probe at 49.995,339.999 is z=398.337500 Tap drift (diff=0.9625mm) — reset probe at 49.995,339.999 is z=397.665000 Tap drift (diff=0.6725mm) — reset probe at 49.995,339.999 is z=396.902500 Tap drift (diff=0.7625mm) — reset probe at 49.995,339.999 is z=396.202500 Tap drift (diff=0.7000mm) — reset probe at 49.995,339.999 is z=395.380000 Tap drift (diff=0.8225mm) — reset probe at 49.995,339.999 is z=394.430000 Tap drift (diff=0.9500mm) — reset

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.730000 probe at 49.998,339.999 is z=498.437500 Tap rejete (vibration chassis, z=498.4375 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,339.999 is z=144.922500 probe at 49.998,339.999 is z=86.925000 Tap drift (diff=57.9975mm) — reset probe at 49.998,339.999 is z=1.232500 Tap drift (diff=85.6925mm) — reset probe at 49.998,339.999 is z=1.220000 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=1.210000 Tap OK (diff=0.0100mm, stable 3/5) probe at 49.998,339.999 is z=1.217500 Tap OK (diff=0.0075mm, stable 4/5) probe at 49.998,339.999 is z=1.215000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.2150 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=488.887500 Tap drift (diff=2.7875mm) — reset probe at 49.998,339.999 is z=488.852500 Tap drift (diff=2.7525mm) — reset probe at 49.998,339.999 is z=486.097500 Tap drift (diff=2.7550mm) — reset probe at 49.998,339.999 is z=486.102500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=486.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.105000 Tap OK (diff=0.0025mm, stable 2/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.107500 Tap OK (diff=0.0075mm, stable 2/5)

probe: at 54.997,328.001 bed will contact at z=2.842500 probe: at 54.997,328.001 bed will contact at z=2.845000 probe: at 380.001,328.001 bed will contact at z=2.767500 probe: at 380.001,328.001 bed will contact at z=2.847500 Probe samples exceed tolerance. Retrying... probe: at 380.001,328.001 bed will contact at z=2.830000 probe: at 380.001,328.001 bed will contact at z=2.875000 probe: at 380.001,101.996 bed will contact at z=2.752500 probe: at 380.001,101.996 bed will contact at z=2.825000 probe: at 380.001,101.996 bed will contact at z=2.810000 probe: at 380.001,101.996 bed will contact at z=2.817500 probe: at 54.997,101.996 bed will contact at z=2.955000 probe: at 54.997,101.996 bed will contact at z=2.950000 probe: at 217.505,214.498 bed will contact at z=2.890000 probe: at 217.505,214.498 bed will contact at z=2.892500 probe: at 217.505,214.498 bed will contact at z=2.887500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=2.84250 front right screw : x=397.0, y=298.0, z=2.84750 : adjust CW 00:01 rear right screw : x=397.0, y=72.0, z=2.81000 : adjust CCW 00:04 rear left screw : x=72.0, y=72.0, z=2.95500 : adjust CW 00:14 middle : x=234.5, y=184.5, z=2.89000 : adjust CW 00:06