[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=1A005C000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-30.1797 gap=1.8203 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.5941 gap=1.4059 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.5941 gap=1.4059 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-30.1797 gap=1.8203 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-29.8141 gap=2.1859 (3/4) tap 5: pos=-30.1797 gap=1.8203 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0426 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=269.847500 probe at 65.996,275.995 is z=269.857500 Tap drift (diff=0.0100mm) — reset probe at 65.996,275.995 is z=269.865000 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=269.870000 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.996,275.995 is z=269.880000 probe at 65.996,275.995 is z=272.685000 Tap drift (diff=2.8050mm) — reset probe at 65.996,275.995 is z=269.872500 Tap drift (diff=2.8125mm) — reset probe at 65.996,275.995 is z=269.877500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=269.8800 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=237.615000 probe at 65.999,275.995 is z=240.260000 Tap drift (diff=2.6450mm) — reset probe at 65.999,275.995 is z=243.062500 Tap drift (diff=2.8025mm) — reset probe at 65.999,275.995 is z=245.692500 Tap drift (diff=2.6300mm) — reset probe at 65.999,275.995 is z=248.497500 Tap drift (diff=2.8050mm) — reset probe at 65.999,275.995 is z=251.140000 Tap drift (diff=2.6425mm) — reset probe at 65.999,275.995 is z=253.937500 Tap drift (diff=2.7975mm) — reset probe at 65.999,275.995 is z=256.577500 Tap drift (diff=2.6400mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=249.772500 Tap drift (diff=6.8050mm) — reset probe at 65.999,275.995 is z=252.540000 Tap drift (diff=2.7675mm) — reset probe at 65.999,275.995 is z=201.307500 Tap drift (diff=51.2325mm) — reset probe at 65.999,275.995 is z=1.150000 Tap drift (diff=200.1575mm) — reset probe at 65.999,275.995 is z=1.132500 Tap drift (diff=0.0175mm) — reset probe at 65.999,275.995 is z=1.117500 Tap drift (diff=0.0150mm) — reset probe at 65.999,275.995 is z=1.120000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=1.110000 Tap OK (diff=0.0100mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1100 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.885000

probe: at 67.000,271.004 bed will contact at z=1.027500 probe: at 67.000,271.004 bed will contact at z=1.052500 probe: at 67.000,271.004 bed will contact at z=1.035000 probe: at 267.996,271.004 bed will contact at z=1.107500 probe: at 267.996,271.004 bed will contact at z=1.112500 probe: at 267.996,271.004 bed will contact at z=1.105000 probe: at 267.996,71.995 bed will contact at z=1.117500 probe: at 267.996,71.995 bed will contact at z=1.110000 probe: at 67.000,71.995 bed will contact at z=1.065000 probe: at 67.000,71.995 bed will contact at z=1.080000 probe: at 67.000,71.995 bed will contact at z=1.067500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.03500 front right screw : x=285.0, y=241.0, z=1.10750 : adjust CW 00:09 rear right screw : x=285.0, y=42.0, z=1.11000 : adjust CW 00:09 rear left screw : x=84.0, y=42.0, z=1.06750 : adjust CW 00:04