[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=1B0060000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9719 gap=1.0281 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1919 gap=1.8081 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1919 gap=1.8081 (2/4) tap 4: pos=-29.8019 gap=2.1981 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=457.1797 gap=1.8203 (3/4) tap 5: pos=457.5941 gap=1.4059 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.1919 spread=0.5972mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,340.003 is z=418.360000 probe at 49.995,340.003 is z=412.287500 Tap drift (diff=6.0725mm) — reset probe at 49.995,340.003 is z=412.250000 Tap drift (diff=0.0375mm) — reset probe at 49.995,340.003 is z=415.005000 Tap drift (diff=2.7550mm) — reset probe at 49.995,340.003 is z=412.245000 Tap drift (diff=2.7600mm) — reset probe at 49.995,340.003 is z=412.212500 Tap drift (diff=0.0325mm) — reset probe at 49.995,340.003 is z=412.210000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,340.003 is z=412.207500 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,340.003 is z=412.252500 Tap drift (diff=0.0450mm) — reset probe at 49.995,340.003 is z=412.247500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,340.003 is z=412.242500 Tap OK (diff=0.0050mm, stable 3/5)

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,340.003 is z=495.010000 probe at 49.998,340.003 is z=4.852500 Tap drift (diff=490.1575mm) — reset probe at 49.998,340.003 is z=1.020000 Tap drift (diff=3.8325mm) — reset probe at 49.998,340.003 is z=1.052500 Tap drift (diff=0.0325mm) — reset probe at 49.998,340.003 is z=1.025000 Tap drift (diff=0.0275mm) — reset probe at 49.998,340.003 is z=1.055000 Tap drift (diff=0.0300mm) — reset Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,340.003 is z=1.050000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,340.003 is z=1.022500 Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,340.003 is z=3.780000 Tap drift (diff=2.7575mm) — reset Tap drift (diff=2.7275mm) — reset probe at 49.998,340.003 is z=1.057500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.0550 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,340.003 is z=486.072500 probe at 49.998,340.003 is z=486.067500 probe at 49.998,340.003 is z=488.825000 probe at 49.998,340.003 is z=486.070000 Tap drift (diff=2.7550mm) — reset VALIDATED: trigger_z=486.0700 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,340.003 is z=486.130000 probe at 49.998,340.003 is z=486.122500 Tap OK (diff=0.0075mm, stable 2/5)

probe: at 54.997,315.001 bed will contact at z=2.560000 probe: at 54.997,315.001 bed will contact at z=2.555000 probe: at 54.997,315.001 bed will contact at z=2.575000 probe: at 380.001,315.001 bed will contact at z=2.595000 probe: at 380.001,315.001 bed will contact at z=2.592500 probe: at 380.001,315.001 bed will contact at z=2.585000 probe: at 380.001,83.000 bed will contact at z=1.557500 probe: at 380.001,83.000 bed will contact at z=1.560000 probe: at 380.001,83.000 bed will contact at z=1.565000 probe: at 54.997,83.000 bed will contact at z=1.740000 probe: at 54.997,83.000 bed will contact at z=1.752500 probe: at 54.997,83.000 bed will contact at z=1.742500 probe: at 217.505,202.498 bed will contact at z=1.885000 probe: at 217.505,202.498 bed will contact at z=1.880000 probe: at 217.505,202.498 bed will contact at z=1.862500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=285.0, z=2.56000 front right screw : x=397.0, y=285.0, z=2.59250 : adjust CW 00:04 rear right screw : x=397.0, y=53.0, z=1.56000 : adjust CCW 01:60 rear left screw : x=72.0, y=53.0, z=1.74250 : adjust CCW 01:38 rear left screw : x=234.5, y=172.5, z=1.88000 : adjust CCW 01:22