[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=300;ssr=SSR10DA;lot=20260618;uid=BBA413 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=1C0046000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9847 gap=2.0153 (3/4) tap 5: pos=-30.0091 gap=1.9909 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-30.0091 gap=1.9909 (1/4) tap 3: pos=-29.9847 gap=2.0153 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=202.0... Probing with pressure switch... probe at 31.003,202.004 is z=265.227500 probe at 31.003,202.004 is z=267.107500 Tap rejete (vibration chassis, z=267.1075 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 31.003,202.004 is z=156.377500 probe at 31.003,202.004 is z=157.937500 Tap drift (diff=1.5600mm) — reset probe at 31.003,202.004 is z=156.380000 Tap drift (diff=1.5575mm) — reset probe at 31.003,202.004 is z=157.975000 Tap drift (diff=1.5950mm) — reset probe at 31.003,202.004 is z=157.857500 Tap drift (diff=1.4775mm) — reset probe at 31.003,202.004 is z=157.855000 Tap drift (diff=1.4750mm) — reset probe at 31.003,202.004 is z=156.382500 Tap drift (diff=1.4725mm) — reset probe at 31.003,202.004 is z=157.852500 probe at 31.003,202.004 is z=157.850000 Tap drift (diff=1.4700mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5)

Moving to tap point X=31.0 Y=202.0... Probing with pressure switch... probe at 30.994,202.004 is z=264.935000 probe at 30.994,202.004 is z=0.860000 Tap drift (diff=264.0750mm) — reset probe at 30.994,202.004 is z=2.535000 Tap drift (diff=1.6750mm) — reset probe at 30.994,202.004 is z=2.582500 Tap drift (diff=1.7225mm) — reset probe at 30.994,202.004 is z=2.490000 Tap drift (diff=1.6300mm) — reset probe at 30.994,202.004 is z=0.862500 Tap drift (diff=1.7200mm) — reset probe at 30.994,202.004 is z=2.585000 Tap drift (diff=1.7250mm) — reset probe at 30.994,202.004 is z=2.580000 Tap drift (diff=1.7175mm) — reset probe at 30.994,202.004 is z=2.577500 Tap drift (diff=1.7150mm) — reset probe at 30.994,202.004 is z=2.052500 Tap drift (diff=1.1925mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.8600 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 202.0) ~ point de tap (31.0, 202.0) Z calibration complete! probe at 30.994,202.004 is z=255.900000 VALIDATED: trigger_z=255.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,202.004 is z=257.215000 Tap drift (diff=1.3150mm) — reset probe at 30.994,202.004 is z=258.052500 Tap drift (diff=0.8375mm) — reset probe at 30.994,202.004 is z=255.902500 Tap drift (diff=2.1500mm) — reset probe at 30.994,202.004 is z=257.255000 Tap drift (diff=1.3525mm) — reset Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,202.004 is z=257.415000

probe: at 32.495,205.497 bed will contact at z=1.432500 probe: at 32.495,205.497 bed will contact at z=1.457500 probe: at 32.495,205.497 bed will contact at z=1.495000 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.510000 probe: at 32.495,205.497 bed will contact at z=1.505000 probe: at 32.495,205.497 bed will contact at z=1.440000 probe: at 32.495,205.497 bed will contact at z=1.467500 probe: at 32.495,205.497 bed will contact at z=1.555000 probe: at 32.495,205.497 bed will contact at z=1.515000 probe: at 32.495,205.497 bed will contact at z=1.482500 probe: at 32.495,205.497 bed will contact at z=1.475000 probe: at 206.996,205.497 bed will contact at z=1.387500 probe: at 206.996,205.497 bed will contact at z=1.400000 probe: at 206.996,205.497 bed will contact at z=1.390000 probe: at 206.996,31.995 bed will contact at z=1.282500 probe: at 206.996,31.995 bed will contact at z=1.292500 probe: at 32.495,31.995 bed will contact at z=1.432500 probe: at 32.495,31.995 bed will contact at z=1.457500 probe: at 32.495,31.995 bed will contact at z=1.467500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.48250 front right screw : x=224.0, y=175.5, z=1.39000 : adjust CCW 00:11 rear right screw : x=224.0, y=2.0, z=1.29250 : adjust CCW 00:23 rear left screw : x=49.5, y=2.0, z=1.45750 : adjust CCW 00:03