[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=1D0043000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=456.8141 gap=2.1859 (1/4) tap 3: pos=457.1797 gap=1.8203 (2/4) tap 4: pos=456.8141 gap=2.1859 (3/4) tap 5: pos=457.1797 gap=1.8203 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-18.5941 gap=1.4059 (1/4) tap 3: pos=-18.9597 gap=1.0403 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.3656mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=457.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=412.462500 probe at 49.995,339.999 is z=412.515000 Tap drift (diff=0.0525mm) — reset probe at 49.995,339.999 is z=412.522500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.995,339.999 is z=412.530000 Tap OK (diff=0.0075mm, stable 3/5) probe at 49.995,339.999 is z=412.512500 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=412.507500 Tap OK (diff=0.0050mm, stable 3/5) probe at 49.995,339.999 is z=412.517500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0100mm, stable 2/5) probe at 49.995,339.999 is z=412.532500 Tap drift (diff=0.0250mm) — reset probe at 49.995,339.999 is z=412.525000 probe at 49.995,339.999 is z=412.520000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0075mm, stable 5/5)

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.762500 probe at 49.998,339.999 is z=453.235000 Tap drift (diff=42.5275mm) — reset probe at 49.998,339.999 is z=42.795000 Tap drift (diff=410.4400mm) — reset probe at 49.998,339.999 is z=45.432500 Tap drift (diff=2.6375mm) — reset probe at 49.998,339.999 is z=48.205000 Tap drift (diff=2.7725mm) — reset probe at 49.998,339.999 is z=50.992500 Tap drift (diff=2.7875mm) — reset probe at 49.998,339.999 is z=53.630000 probe at 49.998,339.999 is z=1.042500 Tap drift (diff=52.5875mm) — reset probe at 49.998,339.999 is z=1.092500 Tap drift (diff=0.0500mm) — reset probe at 49.998,339.999 is z=1.095000 Tap OK (diff=0.0025mm, stable 2/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=1.102500 Tap OK (diff=0.0075mm, stable 3/5) probe at 49.998,339.999 is z=1.100000 Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=1.107500 Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=1.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.080000 probe at 49.998,339.999 is z=486.102500 Tap drift (diff=0.0225mm) — reset probe at 49.998,339.999 is z=488.337500 Tap drift (diff=2.2350mm) — reset probe at 49.998,339.999 is z=491.307500 Tap drift (diff=2.9700mm) — reset probe at 49.998,339.999 is z=493.787500 Tap drift (diff=2.4800mm) — reset Tap drift (diff=7.7075mm) — reset

probe: at 54.997,328.001 bed will contact at z=1.200000 probe: at 54.997,328.001 bed will contact at z=1.220000 probe: at 54.997,328.001 bed will contact at z=1.237500 probe: at 380.001,328.001 bed will contact at z=1.142500 probe: at 380.001,328.001 bed will contact at z=1.185000 probe: at 380.001,328.001 bed will contact at z=1.162500 probe: at 380.001,101.996 bed will contact at z=1.250000 probe: at 380.001,101.996 bed will contact at z=1.270000 probe: at 380.001,101.996 bed will contact at z=1.267500 probe: at 54.997,101.996 bed will contact at z=1.310000 probe: at 54.997,101.996 bed will contact at z=1.325000 probe: at 217.505,214.498 bed will contact at z=1.302500 probe: at 217.505,214.498 bed will contact at z=1.327500 probe: at 217.505,214.498 bed will contact at z=1.322500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.22000 front right screw : x=397.0, y=298.0, z=1.16250 : adjust CCW 00:07 rear right screw : x=397.0, y=72.0, z=1.26750 : adjust CW 00:06 rear left screw : x=72.0, y=72.0, z=1.32500 : adjust CW 00:13 middle : x=234.5, y=184.5, z=1.32250 : adjust CW 00:12