[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=210059000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=467.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=467.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-21.1919 gap=1.8081 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-21.4356 spread=0.7800mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-21.1919 gap=1.8081 (1/4) tap 3: pos=-21.5819 gap=1.4181 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-21.1919 spread=0.5850mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-21.1919 gap=1.8081 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.5819 gap=1.4181 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-21.5819 spread=0.5850mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=494.815000 probe at 55.998,334.001 is z=491.767500 Tap drift (diff=3.0475mm) — reset probe at 55.998,334.001 is z=480.842500 Tap drift (diff=10.9250mm) — reset probe at 55.998,334.001 is z=477.967500 Tap drift (diff=2.8750mm) — reset probe at 55.998,334.001 is z=478.120000 Tap drift (diff=0.1525mm) — reset probe at 55.998,334.001 is z=418.805000 Tap drift (diff=59.3150mm) — reset probe at 55.998,334.001 is z=402.765000 Tap drift (diff=16.0400mm) — reset probe at 55.998,334.001 is z=402.747500 Tap drift (diff=0.0175mm) — reset probe at 55.998,334.001 is z=402.760000 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) probe at 55.998,334.001 is z=405.535000 Tap drift (diff=2.7700mm) — reset probe at 55.998,334.001 is z=402.755000

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=340.377500 probe at 56.001,334.001 is z=343.135000 Tap drift (diff=2.7575mm) — reset probe at 56.001,334.001 is z=301.577500 Tap drift (diff=41.5575mm) — reset probe at 56.001,334.001 is z=170.982500 Tap drift (diff=130.5950mm) — reset probe at 56.001,334.001 is z=113.137500 Tap drift (diff=57.8450mm) — reset probe at 56.001,334.001 is z=99.860000 Tap drift (diff=13.2775mm) — reset probe at 56.001,334.001 is z=101.735000 Tap drift (diff=1.8750mm) — reset probe at 56.001,334.001 is z=98.500000 Tap drift (diff=3.2350mm) — reset probe at 56.001,334.001 is z=76.222500 Tap drift (diff=22.2775mm) — reset probe at 56.001,334.001 is z=55.012500 Tap drift (diff=21.2100mm) — reset probe at 56.001,334.001 is z=57.500000 Tap drift (diff=2.4875mm) — reset probe at 56.001,334.001 is z=58.282500 Tap drift (diff=0.7825mm) — reset probe at 56.001,334.001 is z=61.010000 Tap drift (diff=2.7275mm) — reset probe at 56.001,334.001 is z=33.860000 Tap drift (diff=27.1500mm) — reset probe at 56.001,334.001 is z=27.575000 Tap drift (diff=6.2850mm) — reset probe at 56.001,334.001 is z=29.702500 Tap drift (diff=2.1275mm) — reset probe at 56.001,334.001 is z=30.577500 Tap drift (diff=0.8750mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 56.001,334.001 is z=24.540000 Tap drift (diff=6.0375mm) — reset probe at 56.001,334.001 is z=26.135000 Tap drift (diff=1.5950mm) — reset

probe: at 56.003,334.994 bed will contact at z=1.472500 probe: at 56.003,334.994 bed will contact at z=1.440000 probe: at 56.003,334.994 bed will contact at z=1.480000 probe: at 388.002,334.994 bed will contact at z=1.465000 probe: at 388.002,334.994 bed will contact at z=1.455000 probe: at 388.002,334.994 bed will contact at z=1.452500 probe: at 388.002,110.001 bed will contact at z=1.357500 probe: at 388.002,110.001 bed will contact at z=1.350000 probe: at 388.002,110.001 bed will contact at z=1.400000 Probe samples exceed tolerance. Retrying... probe: at 388.002,110.001 bed will contact at z=1.392500 probe: at 388.002,110.001 bed will contact at z=1.340000 probe: at 388.002,110.001 bed will contact at z=1.370000 probe: at 388.002,110.001 bed will contact at z=1.332500 probe: at 388.002,110.001 bed will contact at z=1.355000 probe: at 56.003,110.001 bed will contact at z=1.495000 probe: at 56.003,110.001 bed will contact at z=1.487500 probe: at 221.996,222.004 bed will contact at z=1.495000 probe: at 221.996,222.004 bed will contact at z=1.485000 probe: at 221.996,222.004 bed will contact at z=1.482500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.47250 front right screw : x=405.0, y=305.0, z=1.45500 : adjust CCW 00:02 rear right screw : x=405.0, y=80.0, z=1.35500 : adjust CCW 00:14 rear left screw : x=73.0, y=80.0, z=1.48750 : adjust CW 00:02 rear middle screw : x=239.0, y=192.0, z=1.48500 : adjust CW 00:02