[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=300;ssr=SSR10DA;lot=20260618;uid=BBA413 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=220046000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=255.9847 gap=2.0153 (1/4) tap 3: pos=256.0091 gap=1.9909 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9847 gap=2.0153 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9938 spread=0.0244mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.8141 gap=2.1859 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9512 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.8141 gap=2.1859 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9512 spread=0.1828mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=256.0091 gap=1.9909 (1/4) tap 3: pos=256.7769 gap=1.2231 (2/4) tap 4: pos=256.7647 gap=1.2353 (3/4) tap 5: pos=256.7769 gap=1.2231 fenetre=0.7678/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=256.5819 spread=0.7678mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=-29.8141 gap=2.1859 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.1797 gap=1.8203 (3/4) tap 5: pos=-29.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9512 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=162.350000 probe at 31.003,211.998 is z=162.352500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=162.3500 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=1.147500 probe at 30.994,211.998 is z=1.177500 Tap drift (diff=0.0300mm) — reset probe at 30.994,211.998 is z=1.180000 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=1.182500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 30.994,211.998 is z=1.150000 Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1825 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=256.092500 probe at 30.994,211.998 is z=256.100000 Tap OK (diff=0.0075mm, stable 2/5) probe at 30.994,211.998 is z=256.097500 probe at 30.994,211.998 is z=256.102500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=256.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=256.095000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=256.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 30.994,211.998 is z=256.065000 Tap drift (diff=0.0325mm) — reset Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=256.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0050mm, stable 2/5) Tap drift (diff=0.0275mm) — reset probe at 30.994,211.998 is z=256.067500 Tap drift (diff=0.0250mm) — reset probe at 30.994,211.998 is z=256.070000 probe at 30.994,211.998 is z=256.105000 probe at 30.994,211.998 is z=256.075000 Tap OK (diff=0.0050mm, stable 3/5) VALIDATED: trigger_z=256.0950 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000)

probe: at 32.495,205.497 bed will contact at z=1.037500 probe: at 32.495,205.497 bed will contact at z=0.957500 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=0.962500 probe: at 32.495,205.497 bed will contact at z=1.002500 probe: at 32.495,205.497 bed will contact at z=0.947500 probe: at 32.495,205.497 bed will contact at z=0.895000 probe: at 32.495,205.497 bed will contact at z=0.972500 probe: at 32.495,205.497 bed will contact at z=0.945000 probe: at 32.495,205.497 bed will contact at z=0.975000 probe: at 206.996,205.497 bed will contact at z=0.980000 probe: at 206.996,205.497 bed will contact at z=0.975000 probe: at 206.996,205.497 bed will contact at z=0.987500 probe: at 206.996,31.995 bed will contact at z=0.912500 probe: at 206.996,31.995 bed will contact at z=0.930000 probe: at 206.996,31.995 bed will contact at z=0.920000 probe: at 32.495,31.995 bed will contact at z=0.875000 probe: at 32.495,31.995 bed will contact at z=0.972500 probe: at 32.495,31.995 bed will contact at z=0.982500 probe: at 32.495,31.995 bed will contact at z=0.945000 probe: at 32.495,31.995 bed will contact at z=0.962500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=0.96250 front right screw : x=224.0, y=175.5, z=0.98000 : adjust CW 00:02 rear right screw : x=224.0, y=2.0, z=0.92000 : adjust CCW 00:05 rear left screw : x=49.5, y=2.0, z=0.96250 : adjust CCW 00:00