[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=230040000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4234 gap=1.5766 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.8012 gap=1.1988 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.3991 gap=1.6009 (3/4) tap 5: pos=-18.3747 gap=1.6253 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.5819 spread=0.4022mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.4112 gap=1.5888 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.2955 spread=0.7800mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=412.087500 probe at 49.995,339.999 is z=412.097500 Tap drift (diff=0.0100mm) — reset probe at 49.995,339.999 is z=412.102500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=412.105000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.995,339.999 is z=412.110000 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=412.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=365.340000 probe at 49.998,339.999 is z=289.397500 Tap drift (diff=75.9425mm) — reset probe at 49.998,339.999 is z=291.730000 Tap drift (diff=2.3325mm) — reset probe at 49.998,339.999 is z=293.730000 Tap drift (diff=2.0000mm) — reset probe at 49.998,339.999 is z=226.125000 Tap drift (diff=67.6050mm) — reset probe at 49.998,339.999 is z=228.755000 Tap drift (diff=2.6300mm) — reset probe at 49.998,339.999 is z=231.575000 Tap drift (diff=2.8200mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=209.840000 Tap drift (diff=21.7350mm) — reset probe at 49.998,339.999 is z=205.695000 Tap drift (diff=4.1450mm) — reset probe at 49.998,339.999 is z=199.320000 Tap drift (diff=6.3750mm) — reset probe at 49.998,339.999 is z=60.082500 Tap drift (diff=139.2375mm) — reset probe at 49.998,339.999 is z=1.235000 Tap drift (diff=58.8475mm) — reset probe at 49.998,339.999 is z=1.240000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,339.999 is z=1.245000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=1.247500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.2475 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.097500 Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=486.100000 Tap OK (diff=0.0025mm, stable 3/5)

probe: at 54.997,328.001 bed will contact at z=1.337500 probe: at 54.997,328.001 bed will contact at z=1.345000 probe: at 380.001,328.001 bed will contact at z=1.255000 probe: at 380.001,328.001 bed will contact at z=1.245000 probe: at 380.001,101.996 bed will contact at z=1.145000 probe: at 380.001,101.996 bed will contact at z=1.172500 probe: at 380.001,101.996 bed will contact at z=1.155000 probe: at 54.997,101.996 bed will contact at z=1.230000 probe: at 54.997,101.996 bed will contact at z=1.235000 probe: at 217.505,214.498 bed will contact at z=1.242500 probe: at 217.505,214.498 bed will contact at z=1.282500 probe: at 217.505,214.498 bed will contact at z=1.280000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.34500 front right screw : x=397.0, y=298.0, z=1.25500 : adjust CCW 00:11 rear right screw : x=397.0, y=72.0, z=1.15500 : adjust CCW 00:23 rear left screw : x=72.0, y=72.0, z=1.23000 : adjust CCW 00:14 middle : x=234.5, y=184.5, z=1.28000 : adjust CCW 00:08