[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=26005C000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=-30.9597 gap=1.0403 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.5941 gap=1.4059 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 150mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=286.402500 probe at 65.996,275.995 is z=286.382500 Tap drift (diff=0.0200mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=286.3825 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.350000 probe at 65.999,275.995 is z=397.752500 Tap rejete (vibration chassis, z=397.7525 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=397.177500 Tap rejete (vibration chassis, z=397.1775 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 65.999,275.995 is z=396.472500 probe at 65.999,275.995 is z=399.095000 Tap rejete (vibration chassis, z=399.0950 > max-z_hop) -> pas de remontee, on poursuit la descente (3) probe at 65.999,275.995 is z=398.407500 Tap rejete (vibration chassis, z=398.4075 > max-z_hop) -> pas de remontee, on poursuit la descente (4) probe at 65.999,275.995 is z=397.750000 Tap rejete (vibration chassis, z=397.7500 > max-z_hop) -> pas de remontee, on poursuit la descente (5) probe at 65.999,275.995 is z=397.335000 Tap rejete (vibration chassis, z=397.3350 > max-z_hop) -> pas de remontee, on poursuit la descente (6) probe at 65.999,275.995 is z=396.790000 probe at 65.999,275.995 is z=399.412500 Tap rejete (vibration chassis, z=399.4125 > max-z_hop) -> pas de remontee, on poursuit la descente (7) probe at 65.999,275.995 is z=398.727500 Tap rejete (vibration chassis, z=398.7275 > max-z_hop) -> pas de remontee, on poursuit la descente (8) probe at 65.999,275.995 is z=398.070000 Tap rejete (vibration chassis, z=398.0700 > max-z_hop) -> pas de remontee, on poursuit la descente (9) probe at 65.999,275.995 is z=397.447500 Tap rejete (vibration chassis, z=397.4475 > max-z_hop) -> pas de remontee, on poursuit la descente (10) probe at 65.999,275.995 is z=397.035000 Tap rejete (vibration chassis, z=397.0350 > max-z_hop) -> pas de remontee, on poursuit la descente (11) probe at 65.999,275.995 is z=396.470000 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=398.705000 Tap rejete (vibration chassis, z=398.7050 > max-z_hop) -> pas de remontee, on poursuit la descente (12) probe at 65.999,275.995 is z=397.907500 Tap rejete (vibration chassis, z=397.9075 > max-z_hop) -> pas de remontee, on poursuit la descente (13) probe at 65.999,275.995 is z=397.252500 Tap rejete (vibration chassis, z=397.2525 > max-z_hop) -> pas de remontee, on poursuit la descente (14) probe at 65.999,275.995 is z=396.645000 probe at 65.999,275.995 is z=399.255000 Tap rejete (vibration chassis, z=399.2550 > max-z_hop) -> pas de remontee, on poursuit la descente (15) probe at 65.999,275.995 is z=398.707500 Tap rejete (vibration chassis, z=398.7075 > max-z_hop) -> pas de remontee, on poursuit la descente (16)

probe: at 67.000,271.004 bed will contact at z=2.467500 probe: at 67.000,271.004 bed will contact at z=2.462500 probe: at 67.000,271.004 bed will contact at z=2.457500 probe: at 267.996,271.004 bed will contact at z=2.437500 probe: at 267.996,271.004 bed will contact at z=2.442500 probe: at 267.996,271.004 bed will contact at z=2.490000 Probe samples exceed tolerance. Retrying... probe: at 267.996,271.004 bed will contact at z=2.435000 probe: at 267.996,271.004 bed will contact at z=2.452500 probe: at 267.996,271.004 bed will contact at z=2.417500 probe: at 267.996,71.995 bed will contact at z=2.510000 probe: at 267.996,71.995 bed will contact at z=2.505000 probe: at 267.996,71.995 bed will contact at z=2.492500 probe: at 67.000,71.995 bed will contact at z=2.470000 probe: at 67.000,71.995 bed will contact at z=2.482500 probe: at 67.000,71.995 bed will contact at z=2.492500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=2.46250 front right screw : x=285.0, y=241.0, z=2.43500 : adjust CCW 00:03 rear right screw : x=285.0, y=42.0, z=2.50500 : adjust CW 00:05 rear left screw : x=84.0, y=42.0, z=2.48250 : adjust CW 00:02