[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=26005D000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.3991 gap=1.6009 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.2924 spread=0.7800mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-18.5819 gap=1.4181 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.1431 spread=0.5850mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=434.252500 probe at 49.995,339.999 is z=428.902500 Tap drift (diff=5.3500mm) — reset probe at 49.995,339.999 is z=414.737500 Tap drift (diff=14.1650mm) — reset probe at 49.995,339.999 is z=417.452500 Tap drift (diff=2.7150mm) — reset probe at 49.995,339.999 is z=414.297500 Tap drift (diff=3.1550mm) — reset probe at 49.995,339.999 is z=411.625000 Tap drift (diff=2.6725mm) — reset probe at 49.995,339.999 is z=411.630000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.995,339.999 is z=411.632500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.995,339.999 is z=411.635000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=411.6350 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.525000 probe at 49.998,339.999 is z=498.015000 Tap rejete (vibration chassis, z=498.0150 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,339.999 is z=497.805000 Tap rejete (vibration chassis, z=497.8050 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 49.998,339.999 is z=463.630000 probe at 49.998,339.999 is z=367.000000 Tap drift (diff=96.6300mm) — reset probe at 49.998,339.999 is z=369.775000 Tap drift (diff=2.7750mm) — reset probe at 49.998,339.999 is z=267.485000 Tap drift (diff=102.2900mm) — reset probe at 49.998,339.999 is z=13.985000 Tap drift (diff=253.5000mm) — reset probe at 49.998,339.999 is z=13.992500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=16.767500 probe at 49.998,339.999 is z=14.002500 Tap drift (diff=0.0100mm) — reset probe at 49.998,339.999 is z=14.005000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=14.007500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=15.885000 Tap drift (diff=1.8775mm) — reset probe at 49.998,339.999 is z=13.997500 Tap drift (diff=1.8875mm) — reset Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=14.0075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.097500 probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.102500 probe at 49.998,339.999 is z=486.105000

probe: at 54.997,328.001 bed will contact at z=1.585000 probe: at 54.997,328.001 bed will contact at z=1.590000 probe: at 380.001,328.001 bed will contact at z=1.680000 probe: at 380.001,328.001 bed will contact at z=1.710000 probe: at 380.001,328.001 bed will contact at z=1.672500 probe: at 380.001,101.996 bed will contact at z=1.635000 probe: at 380.001,101.996 bed will contact at z=1.665000 probe: at 380.001,101.996 bed will contact at z=1.625000 probe: at 54.997,101.996 bed will contact at z=1.607500 probe: at 54.997,101.996 bed will contact at z=1.615000 probe: at 54.997,101.996 bed will contact at z=1.612500 probe: at 217.505,214.498 bed will contact at z=1.622500 probe: at 217.505,214.498 bed will contact at z=1.630000 probe: at 217.505,214.498 bed will contact at z=1.617500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.59000 front right screw : x=397.0, y=298.0, z=1.68000 : adjust CW 00:11 rear right screw : x=397.0, y=72.0, z=1.63500 : adjust CW 00:05 rear left screw : x=72.0, y=72.0, z=1.61250 : adjust CW 00:03 middle : x=234.5, y=184.5, z=1.62250 : adjust CW 00:04