← Home · All machines · All YMS reports → · Packed printers · Trash
SmartPi 1
SmartPi 2

27005A000C51353234323830

PASS Grade A Grade B
Model : C235 · Batch : 20260616
Heated bed : 220V · 300W · SSR SSR10DA
QC pad (MAC) : 02813C788EB7
Start : 2026-06-27T05:18:59.651220 · End : 2026-06-27T05:29:39.993050 · Duration : 640 s
Received (server) : 2026-06-27T05:32:46
yumi_config : board=SMART_MAKER_1_X cpu=STM32F401 conn=UART device=C235 x=SMART_TMC2209_V2 y=SMART_TMC2209_V2 z=SMART_TMC2209_V2 e0=SMART_TMC2209_V2 e1=SMART_TMC2209_V2 mx=42BYGH3023-B-22DH my=42BYGH3023-B-22DH mz=42BYGH2216-B-24DH piezo=YN15T-85A1-W100_15-2P pzb=Smart_Z-Offset pzbv=0.2 mains=220V bedw=300 ssr=SSR10DA lot=20260616 uid=61C229

Proof photos (packing)

Switch to mobile pipeline mode
TestResultTimeDetails / log
MCU + firmware PASS 05:18:59
[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=27005A000C51353234323830
Home X PASS 05:19:21
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000
Home Y PASS 05:19:53
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000
Motherboard fan PASS 05:20:28
Part fan PASS 05:20:31
Hotend fan PASS 05:20:34
Hotend heat 220°C PASS 05:20:34
Bed heat 60°C PASS 05:20:36
Cutter (feed+cut) PASS 05:21:57
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''
YMS-2 feed to head PASS 05:22:08
Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK
Z tap home + Zmax PASS 05:24:56
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=136.345000 probe at 31.003,211.998 is z=136.307500 Tap drift (diff=0.0375mm) — reset probe at 31.003,211.998 is z=136.300000 Tap OK (diff=0.0075mm, stable 2/5) probe at 31.003,211.998 is z=136.292500 Tap OK (diff=0.0075mm, stable 3/5) probe at 31.003,211.998 is z=136.282500 Tap drift (diff=0.0100mm) — reset probe at 31.003,211.998 is z=136.277500 Tap OK (diff=0.0050mm, stable 2/5) probe at 31.003,211.998 is z=136.275000 Tap OK (diff=0.0025mm, stable 3/5) probe at 31.003,211.998 is z=136.272500 Tap OK (diff=0.0025mm, stable 4/5) probe at 31.003,211.998 is z=136.270000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=136.2700 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!
Z tap repeatability PASS 05:29:14 OK: 3 taps convergents spread=0.0000mm (tol=0.0500) sur 15 taps | taps=0.8625, 255.8875, 255.9050, 255.8925, 255.8950, 255.8950, 255.9025, 255.8900, 255.8975, 255.9000, 255.8975, 255.8950, 255.8950, 255.9025, 255.8975
Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=19.200000 probe at 30.994,211.998 is z=0.885000 Tap drift (diff=18.3150mm) — reset probe at 30.994,211.998 is z=0.867500 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=0.865000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 30.994,211.998 is z=0.862500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.8625 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=255.930000 probe at 30.994,211.998 is z=255.897500 Tap drift (diff=0.0325mm) — reset probe at 30.994,211.998 is z=255.895000 Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=255.892500 probe at 30.994,211.998 is z=255.887500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=255.8875 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.942500 probe at 30.994,211.998 is z=255.905000 Tap drift (diff=0.0375mm) — reset probe at 30.994,211.998 is z=255.902500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=255.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.935000 VALIDATED: trigger_z=255.8925 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.940000 probe at 30.994,211.998 is z=255.900000 Tap drift (diff=0.0400mm) — reset VALIDATED: trigger_z=255.8950 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Tap drift (diff=0.0475mm) — reset probe at 30.994,211.998 is z=255.947500
Screws tilt PASS 05:29:39
probe: at 32.495,205.497 bed will contact at z=1.790000 probe: at 32.495,205.497 bed will contact at z=1.770000 probe: at 32.495,205.497 bed will contact at z=1.780000 probe: at 206.996,205.497 bed will contact at z=2.755000 probe: at 206.996,205.497 bed will contact at z=2.762500 probe: at 206.996,31.995 bed will contact at z=2.990000 probe: at 206.996,31.995 bed will contact at z=3.002500 probe: at 32.495,31.995 bed will contact at z=2.245000 probe: at 32.495,31.995 bed will contact at z=2.225000 probe: at 32.495,31.995 bed will contact at z=2.230000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.78000 front right screw : x=224.0, y=175.5, z=2.75500 : adjust CW 01:57 rear right screw : x=224.0, y=2.0, z=3.00250 : adjust CW 02:27 rear left screw : x=49.5, y=2.0, z=2.23000 : adjust CW 00:54

History — 3 reports for this machine

QC dateResultQC pad (MAC)Received (server)
2026-06-27T05:18:59.651220 PASS 27005A000C51353234323830 2026-06-27T05:32:46
2026-06-27T05:15:40.608573 FAIL 27005A000C51353234323830 2026-06-27T05:11:16
2026-06-27T05:12:14.888803 FAIL 27005A000C51353234323830 2026-06-27T05:07:45