[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=27005E000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.0091 gap=1.9909 (2/4) tap 4: pos=456.9847 gap=2.0153 (3/4) tap 5: pos=457.0091 gap=1.9909 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9999 spread=0.0244mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9847 gap=2.0153 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9938 spread=0.0122mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9847 gap=2.0153 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9938 spread=0.0122mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=457.0091 gap=1.9909 (1/4) tap 3: pos=456.9847 gap=2.0153 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-18.0091 gap=1.9909 (1/4) tap 3: pos=-17.9847 gap=2.0153 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=416.665000 probe at 49.995,339.999 is z=416.700000 Tap drift (diff=0.0350mm) — reset probe at 49.995,339.999 is z=416.702500 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,339.999 is z=416.705000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=416.7050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=475.852500 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=404.800000 Tap drift (diff=71.0525mm) — reset probe at 49.998,339.999 is z=396.275000 Tap drift (diff=8.5250mm) — reset probe at 49.998,339.999 is z=390.232500 Tap drift (diff=6.0425mm) — reset probe at 49.998,339.999 is z=359.367500 Tap drift (diff=30.8650mm) — reset probe at 49.998,339.999 is z=356.615000 Tap drift (diff=2.7525mm) — reset probe at 49.998,339.999 is z=357.877500 Tap drift (diff=1.2625mm) — reset probe at 49.998,339.999 is z=360.677500 Tap drift (diff=2.8000mm) — reset probe at 49.998,339.999 is z=361.035000 Tap drift (diff=0.3575mm) — reset probe at 49.998,339.999 is z=286.697500 Tap drift (diff=74.3375mm) — reset probe at 49.998,339.999 is z=288.720000 Tap drift (diff=2.0225mm) — reset probe at 49.998,339.999 is z=206.727500 Tap drift (diff=81.9925mm) — reset probe at 49.998,339.999 is z=209.370000 Tap drift (diff=2.6425mm) — reset probe at 49.998,339.999 is z=35.395000 Tap drift (diff=173.9750mm) — reset probe at 49.998,339.999 is z=38.242500 Tap drift (diff=2.8475mm) — reset probe at 49.998,339.999 is z=27.690000 Tap drift (diff=10.5525mm) — reset probe at 49.998,339.999 is z=4.622500 Tap drift (diff=23.0675mm) — reset probe at 49.998,339.999 is z=7.197500 Tap drift (diff=2.5750mm) — reset probe at 49.998,339.999 is z=1.105000 Tap drift (diff=6.0925mm) — reset

probe: at 54.997,328.001 bed will contact at z=1.775000 probe: at 54.997,328.001 bed will contact at z=1.830000 Probe samples exceed tolerance. Retrying... probe: at 54.997,328.001 bed will contact at z=1.827500 probe: at 54.997,328.001 bed will contact at z=1.820000 probe: at 380.001,328.001 bed will contact at z=1.745000 probe: at 380.001,328.001 bed will contact at z=1.762500 probe: at 380.001,101.996 bed will contact at z=1.737500 probe: at 380.001,101.996 bed will contact at z=1.747500 probe: at 380.001,101.996 bed will contact at z=1.740000 probe: at 54.997,101.996 bed will contact at z=1.817500 probe: at 54.997,101.996 bed will contact at z=1.855000 probe: at 54.997,101.996 bed will contact at z=1.847500 probe: at 217.505,214.498 bed will contact at z=1.845000 probe: at 217.505,214.498 bed will contact at z=1.850000 probe: at 217.505,214.498 bed will contact at z=1.852500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.82750 front right screw : x=397.0, y=298.0, z=1.76250 : adjust CCW 00:08 rear right screw : x=397.0, y=72.0, z=1.74000 : adjust CCW 00:10 rear left screw : x=72.0, y=72.0, z=1.84750 : adjust CW 00:02 middle : x=234.5, y=184.5, z=1.85000 : adjust CW 00:03