[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=2C003F000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.8012 gap=1.1988 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-18.0091 gap=1.9909 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-18.0091 gap=1.9909 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.2041 gap=1.7959 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=-18.1919 gap=1.8081 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.5850/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.6306 spread=0.5850mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=404.232500 probe at 49.995,339.999 is z=404.260000 Tap drift (diff=0.0275mm) — reset probe at 49.995,339.999 is z=404.270000 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.995,339.999 is z=404.277500 Tap OK (diff=0.0075mm, stable 4/5) probe at 49.995,339.999 is z=404.280000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=404.2800 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=495.665000 probe at 49.998,339.999 is z=498.305000 Tap rejete (vibration chassis, z=498.3050 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,339.999 is z=486.195000 probe at 49.998,339.999 is z=446.507500 Tap drift (diff=39.6875mm) — reset probe at 49.998,339.999 is z=1.057500 Tap drift (diff=445.4500mm) — reset probe at 49.998,339.999 is z=1.110000 Tap drift (diff=0.0525mm) — reset probe at 49.998,339.999 is z=1.120000 Tap drift (diff=0.0100mm) — reset probe at 49.998,339.999 is z=3.630000 Tap drift (diff=2.5100mm) — reset probe at 49.998,339.999 is z=1.090000 Tap drift (diff=2.5400mm) — reset probe at 49.998,339.999 is z=1.117500 Tap drift (diff=0.0275mm) — reset probe at 49.998,339.999 is z=3.625000 Tap drift (diff=2.5075mm) — reset probe at 49.998,339.999 is z=6.147500 Tap drift (diff=2.5225mm) — reset probe at 49.998,339.999 is z=1.115000 Tap drift (diff=5.0325mm) — reset probe at 49.998,339.999 is z=1.125000 probe at 49.998,339.999 is z=1.132500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=1.130000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=3.787500 Tap drift (diff=2.6575mm) — reset probe at 49.998,339.999 is z=6.307500 Tap drift (diff=2.5200mm) — reset probe at 49.998,339.999 is z=1.127500 Tap drift (diff=5.1800mm) — reset Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=3.627500

probe: at 54.997,328.001 bed will contact at z=2.035000 probe: at 54.997,328.001 bed will contact at z=2.112500 Probe samples exceed tolerance. Retrying... probe: at 54.997,328.001 bed will contact at z=2.077500 probe: at 54.997,328.001 bed will contact at z=2.092500 probe: at 54.997,328.001 bed will contact at z=2.102500 probe: at 380.001,328.001 bed will contact at z=2.092500 probe: at 380.001,328.001 bed will contact at z=2.077500 probe: at 380.001,328.001 bed will contact at z=2.110000 probe: at 380.001,101.996 bed will contact at z=1.975000 probe: at 380.001,101.996 bed will contact at z=1.967500 probe: at 54.997,101.996 bed will contact at z=2.082500 probe: at 54.997,101.996 bed will contact at z=2.080000 probe: at 54.997,101.996 bed will contact at z=2.055000 probe: at 217.505,214.498 bed will contact at z=2.102500 probe: at 217.505,214.498 bed will contact at z=2.095000 probe: at 217.505,214.498 bed will contact at z=2.100000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=2.09250 front right screw : x=397.0, y=298.0, z=2.09250 : adjust CCW 00:00 rear right screw : x=397.0, y=72.0, z=1.97500 : adjust CCW 00:14 rear left screw : x=72.0, y=72.0, z=2.08000 : adjust CCW 00:01 middle : x=234.5, y=184.5, z=2.10000 : adjust CW 00:01