[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=360040000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-20.9847 gap=2.0153 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9938 spread=0.0122mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-21.0091 gap=1.9909 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 100mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9847 gap=2.0153 (1/4) tap 3: pos=-21.0091 gap=1.9909 (2/4) tap 4: pos=-20.9847 gap=2.0153 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9938 spread=0.0244mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=495.600000 probe at 55.998,334.001 is z=496.165000 Tap drift (diff=0.5650mm) — reset probe at 55.998,334.001 is z=499.162500 Tap rejete (vibration chassis, z=499.1625 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 55.998,334.001 is z=459.817500 probe at 55.998,334.001 is z=434.982500 Tap drift (diff=24.8350mm) — reset probe at 55.998,334.001 is z=411.487500 Tap drift (diff=23.4950mm) — reset probe at 55.998,334.001 is z=409.427500 Tap drift (diff=2.0600mm) — reset probe at 55.998,334.001 is z=409.450000 Tap drift (diff=0.0225mm) — reset probe at 55.998,334.001 is z=409.432500 Tap drift (diff=0.0175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 55.998,334.001 is z=410.410000 Tap drift (diff=0.9600mm) — reset probe at 55.998,334.001 is z=410.725000 Tap drift (diff=0.3150mm) — reset

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=495.292500 probe at 56.001,334.001 is z=497.542500 Tap rejete (vibration chassis, z=497.5425 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 56.001,334.001 is z=361.585000 probe at 56.001,334.001 is z=361.465000 Tap drift (diff=0.1200mm) — reset probe at 56.001,334.001 is z=358.980000 Tap drift (diff=2.4850mm) — reset probe at 56.001,334.001 is z=352.860000 Tap drift (diff=6.1200mm) — reset probe at 56.001,334.001 is z=329.385000 Tap drift (diff=23.4750mm) — reset probe at 56.001,334.001 is z=324.582500 Tap drift (diff=4.8025mm) — reset probe at 56.001,334.001 is z=313.870000 Tap drift (diff=10.7125mm) — reset probe at 56.001,334.001 is z=300.455000 Tap drift (diff=13.4150mm) — reset probe at 56.001,334.001 is z=263.870000 Tap drift (diff=36.5850mm) — reset probe at 56.001,334.001 is z=263.902500 Tap drift (diff=0.0325mm) — reset probe at 56.001,334.001 is z=65.297500 Tap drift (diff=198.6050mm) — reset probe at 56.001,334.001 is z=1.105000 Tap drift (diff=64.1925mm) — reset probe at 56.001,334.001 is z=1.237500 Tap drift (diff=0.1325mm) — reset probe at 56.001,334.001 is z=1.270000 probe at 56.001,334.001 is z=1.265000 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) probe at 56.001,334.001 is z=1.272500 Tap OK (diff=0.0025mm, stable 4/5) probe at 56.001,334.001 is z=1.540000 Tap drift (diff=0.2675mm) — reset probe at 56.001,334.001 is z=1.300000 Tap drift (diff=0.2400mm) — reset

probe: at 56.003,334.994 bed will contact at z=1.235000 probe: at 56.003,334.994 bed will contact at z=1.335000 Probe samples exceed tolerance. Retrying... probe: at 56.003,334.994 bed will contact at z=1.340000 probe: at 56.003,334.994 bed will contact at z=1.337500 probe: at 388.002,334.994 bed will contact at z=1.257500 probe: at 388.002,334.994 bed will contact at z=1.290000 probe: at 388.002,334.994 bed will contact at z=1.292500 probe: at 388.002,110.001 bed will contact at z=1.110000 probe: at 388.002,110.001 bed will contact at z=1.175000 probe: at 388.002,110.001 bed will contact at z=1.132500 probe: at 388.002,110.001 bed will contact at z=1.117500 probe: at 388.002,110.001 bed will contact at z=1.107500 probe: at 56.003,110.001 bed will contact at z=1.180000 probe: at 56.003,110.001 bed will contact at z=1.265000 probe: at 56.003,110.001 bed will contact at z=1.262500 probe: at 56.003,110.001 bed will contact at z=1.272500 probe: at 56.003,110.001 bed will contact at z=1.275000 probe: at 221.996,222.004 bed will contact at z=1.230000 probe: at 221.996,222.004 bed will contact at z=1.270000 probe: at 221.996,222.004 bed will contact at z=1.272500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.33750 front right screw : x=405.0, y=305.0, z=1.29000 : adjust CCW 00:06 rear right screw : x=405.0, y=80.0, z=1.11750 : adjust CCW 00:26 rear left screw : x=73.0, y=80.0, z=1.27250 : adjust CCW 00:08 rear middle screw : x=239.0, y=192.0, z=1.27000 : adjust CCW 00:08