[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=37003F000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-21.3747 gap=1.6253 (1/4) tap 3: pos=-21.3991 gap=1.6009 (2/4) tap 4: pos=-21.3747 gap=1.6253 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-21.4813 spread=0.4022mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=466.9847 gap=2.0153 (1/4) tap 3: pos=467.0091 gap=1.9909 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=467.0091 gap=1.9909 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9847 gap=2.0153 (3/4) tap 5: pos=467.0091 gap=1.9909 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9999 spread=0.0244mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=493.975000 probe at 55.998,334.001 is z=496.880000 Tap drift (diff=2.9050mm) — reset probe at 55.998,334.001 is z=413.507500 Tap drift (diff=83.3725mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 55.998,334.001 is z=413.510000 Tap OK (diff=0.0025mm, stable 3/5) probe at 55.998,334.001 is z=416.050000 Tap drift (diff=2.5400mm) — reset probe at 55.998,334.001 is z=413.512500 Tap drift (diff=2.5375mm) — reset Tap OK (diff=0.0050mm, stable 2/5) Tap drift (diff=2.5425mm) — reset probe at 55.998,334.001 is z=413.505000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 55.998,334.001 is z=416.242500 Tap drift (diff=2.7325mm) — reset probe at 55.998,334.001 is z=417.020000

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=495.810000 probe at 56.001,334.001 is z=498.625000 Tap rejete (vibration chassis, z=498.6250 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 56.001,334.001 is z=436.412500 probe at 56.001,334.001 is z=439.082500 Tap drift (diff=2.6700mm) — reset probe at 56.001,334.001 is z=395.537500 Tap drift (diff=43.5450mm) — reset probe at 56.001,334.001 is z=389.082500 Tap drift (diff=6.4550mm) — reset probe at 56.001,334.001 is z=391.527500 Tap drift (diff=2.4450mm) — reset probe at 56.001,334.001 is z=394.402500 Tap drift (diff=2.8750mm) — reset probe at 56.001,334.001 is z=312.575000 Tap drift (diff=81.8275mm) — reset probe at 56.001,334.001 is z=309.555000 Tap drift (diff=3.0200mm) — reset probe at 56.001,334.001 is z=312.367500 Tap drift (diff=2.8125mm) — reset probe at 56.001,334.001 is z=193.162500 Tap drift (diff=119.2050mm) — reset probe at 56.001,334.001 is z=180.157500 Tap drift (diff=13.0050mm) — reset probe at 56.001,334.001 is z=182.922500 Tap drift (diff=2.7650mm) — reset probe at 56.001,334.001 is z=142.127500 Tap drift (diff=40.7950mm) — reset probe at 56.001,334.001 is z=143.150000 Tap drift (diff=1.0225mm) — reset probe at 56.001,334.001 is z=146.095000 Tap drift (diff=2.9450mm) — reset probe at 56.001,334.001 is z=102.800000 Tap drift (diff=43.2950mm) — reset probe at 56.001,334.001 is z=97.052500 Tap drift (diff=5.7475mm) — reset probe at 56.001,334.001 is z=92.102500 Tap drift (diff=4.9500mm) — reset

probe: at 56.003,334.994 bed will contact at z=1.275000 probe: at 56.003,334.994 bed will contact at z=1.272500 probe: at 56.003,334.994 bed will contact at z=1.297500 probe: at 388.002,334.994 bed will contact at z=1.302500 probe: at 388.002,334.994 bed will contact at z=1.292500 probe: at 388.002,334.994 bed will contact at z=1.305000 probe: at 388.002,110.001 bed will contact at z=1.387500 probe: at 388.002,110.001 bed will contact at z=1.377500 probe: at 56.003,110.001 bed will contact at z=1.340000 probe: at 56.003,110.001 bed will contact at z=1.335000 probe: at 221.996,222.004 bed will contact at z=1.335000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.27500 front right screw : x=405.0, y=305.0, z=1.30250 : adjust CW 00:03 rear right screw : x=405.0, y=80.0, z=1.37750 : adjust CW 00:12 rear left screw : x=73.0, y=80.0, z=1.33500 : adjust CW 00:07 rear middle screw : x=239.0, y=192.0, z=1.33500 : adjust CW 00:07