[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=380059000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.8019 gap=2.1981 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9481 spread=0.1950mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1919 gap=1.8081 (2/4) tap 4: pos=456.8019 gap=2.1981 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=409.225000 probe at 49.995,339.999 is z=409.245000 Tap drift (diff=0.0200mm) — reset probe at 49.995,339.999 is z=409.215000 Tap drift (diff=0.0300mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=409.240000 Tap drift (diff=0.0250mm) — reset probe at 49.995,339.999 is z=409.150000 Tap drift (diff=0.0900mm) — reset probe at 49.995,339.999 is z=409.232500 Tap drift (diff=0.0825mm) — reset probe at 49.995,339.999 is z=409.157500 Tap drift (diff=0.0750mm) — reset probe at 49.995,339.999 is z=409.222500 Tap drift (diff=0.0650mm) — reset probe at 49.995,339.999 is z=409.247500 probe at 49.995,339.999 is z=409.250000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,339.999 is z=409.260000 Tap drift (diff=0.0100mm) — reset

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=1.217500 probe at 49.998,339.999 is z=1.237500 Tap drift (diff=0.0200mm) — reset probe at 49.998,339.999 is z=1.222500 Tap drift (diff=0.0150mm) — reset probe at 49.998,339.999 is z=1.235000 Tap drift (diff=0.0125mm) — reset probe at 49.998,339.999 is z=1.227500 Tap OK (diff=0.0075mm, stable 2/5) Tap drift (diff=0.0100mm) — reset probe at 49.998,339.999 is z=1.230000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=1.252500 probe at 49.998,339.999 is z=1.232500 probe at 49.998,339.999 is z=1.127500 Tap drift (diff=0.1050mm) — reset probe at 49.998,339.999 is z=1.242500 Tap drift (diff=0.1150mm) — reset Tap OK (diff=0.0100mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=1.240000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.2400 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.090000 probe at 49.998,339.999 is z=486.102500 probe at 49.998,339.999 is z=486.100000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.998,339.999 is z=486.107500 Tap OK (diff=0.0075mm, stable 4/5) probe at 49.998,339.999 is z=486.095000 probe at 49.998,339.999 is z=486.097500 probe at 49.998,339.999 is z=486.092500 Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=486.0925 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000)

probe: at 54.997,328.001 bed will contact at z=2.525000 probe: at 54.997,328.001 bed will contact at z=2.537500 probe: at 54.997,328.001 bed will contact at z=2.540000 probe: at 380.001,328.001 bed will contact at z=2.492500 probe: at 380.001,328.001 bed will contact at z=2.502500 probe: at 380.001,328.001 bed will contact at z=2.500000 probe: at 380.001,101.996 bed will contact at z=2.347500 probe: at 380.001,101.996 bed will contact at z=2.362500 probe: at 380.001,101.996 bed will contact at z=2.385000 probe: at 54.997,101.996 bed will contact at z=2.422500 probe: at 54.997,101.996 bed will contact at z=2.425000 probe: at 54.997,101.996 bed will contact at z=2.430000 probe: at 217.505,214.498 bed will contact at z=2.537500 probe: at 217.505,214.498 bed will contact at z=2.542500 probe: at 217.505,214.498 bed will contact at z=2.520000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=2.53750 front right screw : x=397.0, y=298.0, z=2.50000 : adjust CCW 00:04 rear right screw : x=397.0, y=72.0, z=2.36250 : adjust CCW 00:21 rear left screw : x=72.0, y=72.0, z=2.42500 : adjust CCW 00:13 middle : x=234.5, y=184.5, z=2.53750 : adjust CCW 00:00