[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=3D0046000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-18.3625 gap=1.6375 (1/4) tap 3: pos=-18.4112 gap=1.5888 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.4144/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.1919 spread=0.4144mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=411.082500 probe at 49.995,339.999 is z=411.117500 Tap drift (diff=0.0350mm) — reset probe at 49.995,339.999 is z=411.120000 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.995,339.999 is z=411.002500 Tap drift (diff=0.1175mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=411.000000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=411.0000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=474.860000 probe at 49.998,339.999 is z=468.507500 Tap drift (diff=6.3525mm) — reset probe at 49.998,339.999 is z=327.665000 Tap drift (diff=140.8425mm) — reset probe at 49.998,339.999 is z=324.482500 Tap drift (diff=3.1825mm) — reset probe at 49.998,339.999 is z=326.657500 Tap drift (diff=2.1750mm) — reset probe at 49.998,339.999 is z=249.160000 Tap drift (diff=77.4975mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 49.998,339.999 is z=180.817500 Tap drift (diff=68.3425mm) — reset probe at 49.998,339.999 is z=183.672500 Tap drift (diff=2.8550mm) — reset probe at 49.998,339.999 is z=155.312500 Tap drift (diff=28.3600mm) — reset probe at 49.998,339.999 is z=86.775000 Tap drift (diff=68.5375mm) — reset probe at 49.998,339.999 is z=88.727500 Tap drift (diff=1.9525mm) — reset probe at 49.998,339.999 is z=1.255000 Tap drift (diff=87.4725mm) — reset probe at 49.998,339.999 is z=1.332500 Tap drift (diff=0.0775mm) — reset probe at 49.998,339.999 is z=1.295000 Tap drift (diff=0.0375mm) — reset probe at 49.998,339.999 is z=1.152500 Tap drift (diff=0.1425mm) — reset Tap drift (diff=0.1800mm) — reset probe at 49.998,339.999 is z=1.302500 Tap drift (diff=0.0300mm) — reset probe at 49.998,339.999 is z=1.352500 Tap drift (diff=0.0500mm) — reset probe at 49.998,339.999 is z=1.327500 Tap drift (diff=0.0250mm) — reset probe at 49.998,339.999 is z=1.347500

probe: at 54.997,328.001 bed will contact at z=1.787500 probe: at 54.997,328.001 bed will contact at z=1.782500 probe: at 380.001,328.001 bed will contact at z=1.705000 probe: at 380.001,328.001 bed will contact at z=1.692500 probe: at 380.001,328.001 bed will contact at z=1.695000 probe: at 380.001,101.996 bed will contact at z=1.775000 probe: at 380.001,101.996 bed will contact at z=1.750000 probe: at 380.001,101.996 bed will contact at z=1.780000 probe: at 54.997,101.996 bed will contact at z=1.760000 probe: at 54.997,101.996 bed will contact at z=1.762500 probe: at 217.505,214.498 bed will contact at z=1.770000 probe: at 217.505,214.498 bed will contact at z=1.762500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.78250 front right screw : x=397.0, y=298.0, z=1.69500 : adjust CCW 00:10 rear right screw : x=397.0, y=72.0, z=1.77500 : adjust CCW 00:01 rear left screw : x=72.0, y=72.0, z=1.76000 : adjust CCW 00:03 middle : x=234.5, y=184.5, z=1.77000 : adjust CCW 00:01