[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=3E0061000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.8141 gap=2.1859 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=357.1797 gap=1.8203 (3/4) tap 5: pos=356.8141 gap=2.1859 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9512 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=285.982500 probe at 65.996,275.995 is z=286.000000 Tap drift (diff=0.0175mm) — reset probe at 65.996,275.995 is z=286.005000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=286.010000 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.996,275.995 is z=286.012500 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.996,275.995 is z=286.015000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=286.0150 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.775000 probe at 65.999,275.995 is z=309.045000 Tap drift (diff=86.7300mm) — reset probe at 65.999,275.995 is z=307.975000 Tap drift (diff=1.0700mm) — reset probe at 65.999,275.995 is z=300.652500 Tap drift (diff=7.3225mm) — reset probe at 65.999,275.995 is z=293.772500 Tap drift (diff=6.8800mm) — reset probe at 65.999,275.995 is z=286.852500 Tap drift (diff=6.9200mm) — reset probe at 65.999,275.995 is z=282.447500 Tap drift (diff=4.4050mm) — reset probe at 65.999,275.995 is z=268.660000 Tap drift (diff=13.7875mm) — reset probe at 65.999,275.995 is z=266.145000 Tap drift (diff=2.5150mm) — reset probe at 65.999,275.995 is z=268.980000 Tap drift (diff=2.8350mm) — reset probe at 65.999,275.995 is z=0.915000 Tap drift (diff=268.0650mm) — reset probe at 65.999,275.995 is z=0.935000 Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=3.690000 Tap drift (diff=2.7550mm) — reset probe at 65.999,275.995 is z=6.450000 Tap drift (diff=2.7600mm) — reset probe at 65.999,275.995 is z=0.940000 Tap drift (diff=5.5100mm) — reset probe at 65.999,275.995 is z=3.687500 Tap drift (diff=2.7475mm) — reset probe at 65.999,275.995 is z=6.447500 probe at 65.999,275.995 is z=0.942500 Tap drift (diff=5.5050mm) — reset probe at 65.999,275.995 is z=0.945000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=0.947500 Tap OK (diff=0.0025mm, stable 3/5)

probe: at 67.000,271.004 bed will contact at z=1.800000 probe: at 67.000,271.004 bed will contact at z=1.792500 probe: at 67.000,271.004 bed will contact at z=1.785000 probe: at 267.996,271.004 bed will contact at z=1.687500 probe: at 267.996,271.004 bed will contact at z=1.660000 probe: at 267.996,271.004 bed will contact at z=1.655000 probe: at 267.996,71.995 bed will contact at z=1.732500 probe: at 267.996,71.995 bed will contact at z=1.740000 probe: at 267.996,71.995 bed will contact at z=1.737500 probe: at 67.000,71.995 bed will contact at z=1.765000 probe: at 67.000,71.995 bed will contact at z=1.742500 probe: at 67.000,71.995 bed will contact at z=1.747500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.79250 front right screw : x=285.0, y=241.0, z=1.66000 : adjust CCW 00:16 rear right screw : x=285.0, y=42.0, z=1.73750 : adjust CCW 00:07 rear left screw : x=84.0, y=42.0, z=1.74750 : adjust CCW 00:05