[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=3F0045000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-30.1797 gap=1.8203 (1/4) tap 3: pos=-29.8141 gap=2.1859 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5575 gap=1.4425 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-30.5941 gap=1.4059 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1462 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=265.305000 probe at 31.003,211.998 is z=267.707500 Tap rejete (vibration chassis, z=267.7075 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 31.003,211.998 is z=183.822500 probe at 31.003,211.998 is z=176.217500 Tap drift (diff=7.6050mm) — reset probe at 31.003,211.998 is z=176.215000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=176.2150 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=0.832500 probe at 30.994,211.998 is z=0.837500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=0.8375 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=265.580000 probe at 30.994,211.998 is z=268.012500 Tap rejete (vibration chassis, z=268.0125 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 30.994,211.998 is z=255.900000 Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=255.895000 VALIDATED: trigger_z=255.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=265.545000 Tap drift (diff=9.6450mm) — reset Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) probe at 30.994,211.998 is z=265.497500 probe at 30.994,211.998 is z=255.897500 Tap drift (diff=9.6000mm) — reset probe at 30.994,211.998 is z=258.252500 Tap drift (diff=2.3550mm) — reset VALIDATED: trigger_z=255.8975 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=265.372500 probe at 30.994,211.998 is z=267.767500 Tap rejete (vibration chassis, z=267.7675 > max-z_hop) -> pas de remontee, on poursuit la descente (1) Tap OK (diff=0.0025mm, stable 2/5) probe at 30.994,211.998 is z=265.457500 Tap drift (diff=9.5575mm) — reset probe at 30.994,211.998 is z=258.332500 Tap drift (diff=2.4325mm) — reset Tap drift (diff=2.3525mm) — reset probe at 30.994,211.998 is z=265.370000 probe at 30.994,211.998 is z=267.772500 Tap rejete (vibration chassis, z=267.7725 > max-z_hop) -> pas de remontee, on poursuit la descente (1)

probe: at 32.495,205.497 bed will contact at z=0.777500 probe: at 32.495,205.497 bed will contact at z=0.815000 probe: at 32.495,205.497 bed will contact at z=0.797500 probe: at 206.996,205.497 bed will contact at z=2.595000 probe: at 206.996,205.497 bed will contact at z=2.600000 probe: at 206.996,205.497 bed will contact at z=2.597500 probe: at 206.996,31.995 bed will contact at z=3.680000 probe: at 206.996,31.995 bed will contact at z=3.675000 probe: at 32.495,31.995 bed will contact at z=2.445000 probe: at 32.495,31.995 bed will contact at z=2.437500 probe: at 32.495,31.995 bed will contact at z=2.422500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=0.79750 front right screw : x=224.0, y=175.5, z=2.59750 : adjust CW 03:36 rear right screw : x=224.0, y=2.0, z=3.68000 : adjust CW 05:46 rear left screw : x=49.5, y=2.0, z=2.43750 : adjust CW 03:17