[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=430040000D51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.8141 gap=2.1859 (3/4) tap 5: pos=457.1797 gap=1.8203 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.3656mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7891 gap=1.2109 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4234 gap=1.5766 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=457.1797 gap=1.8203 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.1797 gap=1.8203 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=402.572500 probe at 49.995,339.999 is z=401.615000 Tap drift (diff=0.9575mm) — reset probe at 49.995,339.999 is z=401.202500 Tap drift (diff=0.4125mm) — reset probe at 49.995,339.999 is z=400.880000 Tap drift (diff=0.3225mm) — reset probe at 49.995,339.999 is z=400.295000 Tap drift (diff=0.5850mm) — reset probe at 49.995,339.999 is z=399.650000 Tap drift (diff=0.6450mm) — reset probe at 49.995,339.999 is z=398.697500 Tap drift (diff=0.9525mm) — reset probe at 49.995,339.999 is z=398.292500 Tap drift (diff=0.4050mm) — reset probe at 49.995,339.999 is z=400.777500 Tap drift (diff=2.4850mm) — reset probe at 49.995,339.999 is z=400.815000 Tap drift (diff=0.0375mm) — reset probe at 49.995,339.999 is z=400.817500 Tap OK (diff=0.0025mm, stable 2/5)

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=287.320000 probe at 49.998,339.999 is z=250.565000 Tap drift (diff=36.7550mm) — reset probe at 49.998,339.999 is z=212.032500 Tap drift (diff=38.5325mm) — reset probe at 49.998,339.999 is z=207.252500 Tap drift (diff=4.7800mm) — reset probe at 49.998,339.999 is z=206.890000 Tap drift (diff=0.3625mm) — reset probe at 49.998,339.999 is z=199.680000 Tap drift (diff=7.2100mm) — reset probe at 49.998,339.999 is z=177.407500 Tap drift (diff=22.2725mm) — reset probe at 49.998,339.999 is z=165.857500 Tap drift (diff=11.5500mm) — reset probe at 49.998,339.999 is z=1.255000 Tap drift (diff=164.6025mm) — reset probe at 49.998,339.999 is z=1.257500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.2575 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.097500 probe at 49.998,339.999 is z=486.102500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.998,339.999 is z=486.105000 Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=486.100000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=494.447500 Tap drift (diff=8.3500mm) — reset Tap OK (diff=0.0000mm, stable 5/5)

probe: at 54.997,328.001 bed will contact at z=3.330000 probe: at 54.997,328.001 bed will contact at z=3.327500 probe: at 54.997,328.001 bed will contact at z=3.325000 probe: at 380.001,328.001 bed will contact at z=3.240000 probe: at 380.001,328.001 bed will contact at z=3.225000 probe: at 380.001,328.001 bed will contact at z=3.230000 probe: at 380.001,101.996 bed will contact at z=3.232500 probe: at 380.001,101.996 bed will contact at z=3.210000 probe: at 380.001,101.996 bed will contact at z=3.237500 probe: at 54.997,101.996 bed will contact at z=3.300000 probe: at 54.997,101.996 bed will contact at z=3.305000 probe: at 54.997,101.996 bed will contact at z=3.310000 probe: at 217.505,214.498 bed will contact at z=3.355000 probe: at 217.505,214.498 bed will contact at z=3.352500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=3.32750 front right screw : x=397.0, y=298.0, z=3.23000 : adjust CCW 00:12 rear right screw : x=397.0, y=72.0, z=3.23250 : adjust CCW 00:11 rear left screw : x=72.0, y=72.0, z=3.30500 : adjust CCW 00:03 middle : x=234.5, y=184.5, z=3.35250 : adjust CW 00:03