[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=440060000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.770000 probe at 65.996,275.995 is z=398.562500 Tap rejete (vibration chassis, z=398.5625 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.996,275.995 is z=372.007500 probe at 65.996,275.995 is z=374.812500 Tap drift (diff=2.8050mm) — reset probe at 65.996,275.995 is z=377.605000 Tap drift (diff=2.7925mm) — reset probe at 65.996,275.995 is z=380.372500 Tap drift (diff=2.7675mm) — reset probe at 65.996,275.995 is z=300.287500 Tap drift (diff=80.0850mm) — reset probe at 65.996,275.995 is z=300.285000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=300.730000 Tap drift (diff=0.4425mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.996,275.995 is z=300.290000 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.737500 probe at 65.999,275.995 is z=398.467500 Tap rejete (vibration chassis, z=398.4675 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.999,275.995 is z=398.295000 Tap rejete (vibration chassis, z=398.2950 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 65.999,275.995 is z=398.145000 Tap rejete (vibration chassis, z=398.1450 > max-z_hop) -> pas de remontee, on poursuit la descente (3) probe at 65.999,275.995 is z=397.995000 Tap rejete (vibration chassis, z=397.9950 > max-z_hop) -> pas de remontee, on poursuit la descente (4) probe at 65.999,275.995 is z=397.825000 Tap rejete (vibration chassis, z=397.8250 > max-z_hop) -> pas de remontee, on poursuit la descente (5) probe at 65.999,275.995 is z=397.667500 Tap rejete (vibration chassis, z=397.6675 > max-z_hop) -> pas de remontee, on poursuit la descente (6) probe at 65.999,275.995 is z=397.507500 Tap rejete (vibration chassis, z=397.5075 > max-z_hop) -> pas de remontee, on poursuit la descente (7) probe at 65.999,275.995 is z=397.347500 Tap rejete (vibration chassis, z=397.3475 > max-z_hop) -> pas de remontee, on poursuit la descente (8) probe at 65.999,275.995 is z=397.212500 Tap rejete (vibration chassis, z=397.2125 > max-z_hop) -> pas de remontee, on poursuit la descente (9) probe at 65.999,275.995 is z=397.065000 Tap rejete (vibration chassis, z=397.0650 > max-z_hop) -> pas de remontee, on poursuit la descente (10) probe at 65.999,275.995 is z=396.902500 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=399.625000 Tap rejete (vibration chassis, z=399.6250 > max-z_hop) -> pas de remontee, on poursuit la descente (11) probe at 65.999,275.995 is z=399.422500 Tap rejete (vibration chassis, z=399.4225 > max-z_hop) -> pas de remontee, on poursuit la descente (12) probe at 65.999,275.995 is z=399.262500 Tap rejete (vibration chassis, z=399.2625 > max-z_hop) -> pas de remontee, on poursuit la descente (13) probe at 65.999,275.995 is z=399.110000 Tap rejete (vibration chassis, z=399.1100 > max-z_hop) -> pas de remontee, on poursuit la descente (14) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) probe at 65.999,275.995 is z=398.910000 Tap rejete (vibration chassis, z=398.9100 > max-z_hop) -> pas de remontee, on poursuit la descente (15) probe at 65.999,275.995 is z=397.932500 Tap rejete (vibration chassis, z=397.9325 > max-z_hop) -> pas de remontee, on poursuit la descente (16) probe at 65.999,275.995 is z=397.837500 Tap rejete (vibration chassis, z=397.8375 > max-z_hop) -> pas de remontee, on poursuit la descente (17)

probe: at 67.000,271.004 bed will contact at z=1.300000 probe: at 67.000,271.004 bed will contact at z=1.382500 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.337500 probe: at 67.000,271.004 bed will contact at z=1.397500 probe: at 67.000,271.004 bed will contact at z=1.380000 probe: at 67.000,271.004 bed will contact at z=1.365000 probe: at 67.000,271.004 bed will contact at z=1.415000 probe: at 67.000,271.004 bed will contact at z=1.390000 probe: at 67.000,271.004 bed will contact at z=1.357500 probe: at 67.000,271.004 bed will contact at z=1.355000 probe: at 267.996,271.004 bed will contact at z=1.265000 probe: at 267.996,271.004 bed will contact at z=1.270000 probe: at 267.996,271.004 bed will contact at z=1.267500 probe: at 267.996,71.995 bed will contact at z=1.330000 probe: at 267.996,71.995 bed will contact at z=1.327500 probe: at 67.000,71.995 bed will contact at z=1.207500 probe: at 67.000,71.995 bed will contact at z=1.217500 probe: at 67.000,71.995 bed will contact at z=1.245000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.35750 front right screw : x=285.0, y=241.0, z=1.26750 : adjust CCW 00:11 rear right screw : x=285.0, y=42.0, z=1.33000 : adjust CCW 00:03 rear left screw : x=84.0, y=42.0, z=1.21750 : adjust CCW 00:17