[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=46005B000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5575 gap=1.4425 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9719 gap=1.0281 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=256.1797 gap=1.8203 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=256.0091 gap=1.9909 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=256.0456 spread=0.1828mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7891 gap=1.2109 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=256.1919 gap=1.8081 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=175.862500 probe at 31.003,211.998 is z=175.982500 Tap drift (diff=0.1200mm) — reset probe at 31.003,211.998 is z=175.985000 Tap OK (diff=0.0025mm, stable 2/5) probe at 31.003,211.998 is z=176.005000 Tap drift (diff=0.0200mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 31.003,211.998 is z=176.007500 Tap OK (diff=0.0025mm, stable 3/5) probe at 31.003,211.998 is z=176.022500 Tap drift (diff=0.0150mm) — reset probe at 31.003,211.998 is z=176.020000 probe at 31.003,211.998 is z=176.017500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=176.0225 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=113.217500 probe at 30.994,211.998 is z=65.185000 Tap drift (diff=48.0325mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 30.994,211.998 is z=64.495000 Tap drift (diff=0.6900mm) — reset probe at 30.994,211.998 is z=57.255000 Tap drift (diff=7.2400mm) — reset probe at 30.994,211.998 is z=1.225000 Tap drift (diff=56.0300mm) — reset probe at 30.994,211.998 is z=1.242500 Tap drift (diff=0.0175mm) — reset probe at 30.994,211.998 is z=1.245000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=1.247500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.2475 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete! probe at 30.994,211.998 is z=255.900000 probe at 30.994,211.998 is z=255.907500 Tap OK (diff=0.0075mm, stable 2/5) probe at 30.994,211.998 is z=255.910000 VALIDATED: trigger_z=255.9100 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.897500 probe at 30.994,211.998 is z=255.902500 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 30.994,211.998 is z=255.905000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=255.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) VALIDATED: trigger_z=255.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 30.994,211.998 is z=255.912500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 30.994,211.998 is z=255.915000

probe: at 32.495,205.497 bed will contact at z=1.427500 probe: at 32.495,205.497 bed will contact at z=1.480000 Probe samples exceed tolerance. Retrying... probe: at 32.495,205.497 bed will contact at z=1.437500 probe: at 32.495,205.497 bed will contact at z=1.477500 probe: at 32.495,205.497 bed will contact at z=1.447500 probe: at 206.996,205.497 bed will contact at z=4.200000 probe: at 206.996,205.497 bed will contact at z=4.210000 probe: at 206.996,205.497 bed will contact at z=4.212500 probe: at 206.996,31.995 bed will contact at z=5.860000 probe: at 206.996,31.995 bed will contact at z=5.870000 probe: at 206.996,31.995 bed will contact at z=5.865000 probe: at 32.495,31.995 bed will contact at z=3.487500 probe: at 32.495,31.995 bed will contact at z=3.477500 probe: at 32.495,31.995 bed will contact at z=3.530000 probe: at 32.495,31.995 bed will contact at z=3.455000 probe: at 32.495,31.995 bed will contact at z=3.497500 probe: at 32.495,31.995 bed will contact at z=3.515000 probe: at 32.495,31.995 bed will contact at z=3.457500 probe: at 32.495,31.995 bed will contact at z=3.495000 probe: at 32.495,31.995 bed will contact at z=3.517500 probe: at 32.495,31.995 bed will contact at z=3.505000 probe: at 32.495,31.995 bed will contact at z=3.540000 probe: at 32.495,31.995 bed will contact at z=3.547500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.44750 front right screw : x=224.0, y=175.5, z=4.21000 : adjust CW 05:32 rear right screw : x=224.0, y=2.0, z=5.86500 : adjust CW 08:50 rear left screw : x=49.5, y=2.0, z=3.54000 : adjust CW 04:11