[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=460060000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5575 gap=1.4425 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5575 gap=1.4425 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7891 gap=1.2109 (3/4) tap 5: pos=-21.5819 gap=1.4181 fenetre=0.2072/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-21.7312 spread=0.2072mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=495.700000 probe at 55.998,334.001 is z=498.390000 Tap rejete (vibration chassis, z=498.3900 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 55.998,334.001 is z=458.900000 probe at 55.998,334.001 is z=447.550000 Tap drift (diff=11.3500mm) — reset probe at 55.998,334.001 is z=425.705000 Tap drift (diff=21.8450mm) — reset probe at 55.998,334.001 is z=428.432500 Tap drift (diff=2.7275mm) — reset probe at 55.998,334.001 is z=407.390000 Tap drift (diff=21.0425mm) — reset probe at 55.998,334.001 is z=407.395000 Tap OK (diff=0.0050mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=407.3950 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=495.735000 probe at 56.001,334.001 is z=360.495000 Tap drift (diff=135.2400mm) — reset probe at 56.001,334.001 is z=124.137500 Tap drift (diff=236.3575mm) — reset probe at 56.001,334.001 is z=117.170000 Tap drift (diff=6.9675mm) — reset probe at 56.001,334.001 is z=109.472500 Tap drift (diff=7.6975mm) — reset probe at 56.001,334.001 is z=102.692500 Tap drift (diff=6.7800mm) — reset probe at 56.001,334.001 is z=99.107500 Tap drift (diff=3.5850mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 56.001,334.001 is z=63.435000 Tap drift (diff=35.6725mm) — reset probe at 56.001,334.001 is z=1.195000 Tap drift (diff=62.2400mm) — reset probe at 56.001,334.001 is z=1.202500 Tap OK (diff=0.0075mm, stable 2/5) probe at 56.001,334.001 is z=1.205000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=1.2025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete! probe at 56.001,334.001 is z=486.105000 probe at 56.001,334.001 is z=486.110000 Tap OK (diff=0.0050mm, stable 2/5) probe at 56.001,334.001 is z=486.107500 probe at 56.001,334.001 is z=486.100000 Tap OK (diff=0.0075mm, stable 4/5) Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=486.1100 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 56.001,334.001 is z=486.102500

probe: at 56.003,334.994 bed will contact at z=1.077500 probe: at 56.003,334.994 bed will contact at z=1.075000 probe: at 56.003,334.994 bed will contact at z=1.072500 probe: at 388.002,334.994 bed will contact at z=1.025000 probe: at 388.002,334.994 bed will contact at z=1.037500 probe: at 388.002,334.994 bed will contact at z=1.035000 probe: at 388.002,110.001 bed will contact at z=0.980000 probe: at 388.002,110.001 bed will contact at z=0.947500 probe: at 388.002,110.001 bed will contact at z=0.952500 probe: at 56.003,110.001 bed will contact at z=1.025000 probe: at 56.003,110.001 bed will contact at z=1.022500 probe: at 56.003,110.001 bed will contact at z=1.017500 probe: at 221.996,222.004 bed will contact at z=1.095000 probe: at 221.996,222.004 bed will contact at z=1.092500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.07500 front right screw : x=405.0, y=305.0, z=1.03500 : adjust CCW 00:05 rear right screw : x=405.0, y=80.0, z=0.95250 : adjust CCW 00:15 rear left screw : x=73.0, y=80.0, z=1.02250 : adjust CCW 00:06 rear middle screw : x=239.0, y=192.0, z=1.09500 : adjust CW 00:02