← Home · All machines · All YMS reports → · Packed printers · Trash
SmartPi 1
SmartPi 2

490035000F51353135323934

PASS Grade A Grade B
Model : C335 · Batch : 20260618
Heated bed : 220V · 500W · SSR SSR10DA
QC pad (MAC) : 0281D225B2A9
Start : 2026-10-23T04:09:17.167684 · End : 2026-10-23T04:20:45.896112 · Duration : 688 s
Received (server) : 2026-10-23T04:24:21
yumi_config : board=SMART_MAKER_1_X cpu=STM32F401 conn=UART device=C335 x=SMART_TMC2209_V2 y=SMART_TMC2209_V2 z=SMART_TMC2209_V2 e0=SMART_TMC2209_V2 e1=SMART_TMC2209_V2 mx=42BYGH3023-B-22DH my=42BYGH3023-B-22DH mz=42BYGH2216-B-24DH piezo=YN15T-85A1-W100_15-2P pzb=Smart_Z-Offset pzbv=0.2 mains=220V bedw=500 ssr=SSR10DA lot=20260618 uid=36C6E9

Proof photos (packing)

Switch to mobile pipeline mode
TestResultTimeDetails / log
MCU + firmware PASS 04:09:17
[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=490035000F51353135323934
Home X PASS 04:09:42
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000
Home Y PASS 04:10:15
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000
Motherboard fan PASS 04:10:20
Part fan PASS 04:10:23
Hotend fan PASS 04:10:25
Hotend heat 220°C PASS 04:10:37
Bed heat 60°C PASS 04:10:57
Cutter (feed+cut) PASS 04:12:29
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''
YMS-2 feed to head PASS 04:12:44
Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK
Z tap home + Zmax PASS 04:16:03
Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=384.845000 probe at 65.996,275.995 is z=285.935000 Tap drift (diff=98.9100mm) — reset probe at 65.996,275.995 is z=288.367500 Tap drift (diff=2.4325mm) — reset probe at 65.996,275.995 is z=288.537500 Tap drift (diff=2.6025mm) — reset probe at 65.996,275.995 is z=288.535000 Tap drift (diff=2.6000mm) — reset probe at 65.996,275.995 is z=288.697500 Tap drift (diff=2.7625mm) — reset probe at 65.996,275.995 is z=291.495000 Tap drift (diff=2.7975mm) — reset probe at 65.996,275.995 is z=294.250000 Tap drift (diff=2.7550mm) — reset probe at 65.996,275.995 is z=297.010000 Tap drift (diff=2.7600mm) — reset probe at 65.996,275.995 is z=299.740000 Tap drift (diff=2.7300mm) — reset probe at 65.996,275.995 is z=302.452500 Tap drift (diff=2.7125mm) — reset
Z tap repeatability PASS 04:20:14 OK: 3 taps convergents spread=0.0000mm (tol=0.0500) sur 15 taps | taps=1.0725, 386.1075, 386.0975, 386.1000, 386.1025, 386.1000, 386.1025, 386.0975, 386.0975, 386.1000, 386.1025, 386.1000, 386.1000, 386.1000, 386.1000
Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=1.062500 probe at 65.999,275.995 is z=1.070000 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=1.072500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.0725 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=386.100000 probe at 65.999,275.995 is z=386.102500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=386.105000 probe at 65.999,275.995 is z=386.107500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=386.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 65.999,275.995 is z=386.095000 probe at 65.999,275.995 is z=386.097500 Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=386.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 2/5) VALIDATED: trigger_z=386.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) VALIDATED: trigger_z=386.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Tap OK (diff=0.0000mm, stable 3/5)
Screws tilt PASS 04:20:45
probe: at 67.000,271.004 bed will contact at z=0.935000 probe: at 67.000,271.004 bed will contact at z=0.922500 probe: at 67.000,271.004 bed will contact at z=0.937500 probe: at 267.996,271.004 bed will contact at z=0.952500 probe: at 267.996,271.004 bed will contact at z=0.950000 probe: at 267.996,71.995 bed will contact at z=0.980000 probe: at 267.996,71.995 bed will contact at z=0.977500 probe: at 267.996,71.995 bed will contact at z=0.972500 probe: at 67.000,71.995 bed will contact at z=0.987500 probe: at 67.000,71.995 bed will contact at z=0.975000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=0.93500 front right screw : x=285.0, y=241.0, z=0.95250 : adjust CW 00:02 rear right screw : x=285.0, y=42.0, z=0.97750 : adjust CW 00:05 rear left screw : x=84.0, y=42.0, z=0.98750 : adjust CW 00:06

History — 2 reports for this machine

QC dateResultQC pad (MAC)Received (server)
2026-10-23T04:09:17.167684 PASS 490035000F51353135323934 2026-10-23T04:24:21
2026-07-15T08:44:36.005426 FAIL 490035000F51353135323934 2026-07-15T08:51:04