[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=490037000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=467.1919 gap=1.8081 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=467.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=467.1919 gap=1.8081 (3/4) tap 5: pos=466.8019 gap=2.1981 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.3900mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-21.7769 gap=1.2231 (1/4) tap 3: pos=-21.7769 gap=1.2231 (2/4) tap 4: pos=-21.7769 gap=1.2231 (3/4) tap 5: pos=-21.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-21.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=491.837500 probe at 55.998,334.001 is z=466.825000 Tap drift (diff=25.0125mm) — reset probe at 55.998,334.001 is z=458.195000 Tap drift (diff=8.6300mm) — reset probe at 55.998,334.001 is z=460.212500 Tap drift (diff=2.0175mm) — reset probe at 55.998,334.001 is z=412.995000 Tap drift (diff=47.2175mm) — reset probe at 55.998,334.001 is z=413.007500 Tap drift (diff=0.0125mm) — reset probe at 55.998,334.001 is z=413.000000 Tap OK (diff=0.0075mm, stable 2/5) probe at 55.998,334.001 is z=413.002500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 55.998,334.001 is z=413.005000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=413.0050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=147.105000 probe at 56.001,334.001 is z=149.890000 Tap drift (diff=2.7850mm) — reset probe at 56.001,334.001 is z=1.120000 Tap drift (diff=148.7700mm) — reset probe at 56.001,334.001 is z=1.132500 Tap drift (diff=0.0125mm) — reset probe at 56.001,334.001 is z=1.127500 Tap OK (diff=0.0050mm, stable 2/5) probe at 56.001,334.001 is z=1.097500 Tap drift (diff=0.0300mm) — reset probe at 56.001,334.001 is z=1.140000 Tap drift (diff=0.0425mm) — reset probe at 56.001,334.001 is z=1.137500 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0100mm, stable 3/5) Tap OK (diff=0.0000mm, stable 2/5) probe at 56.001,334.001 is z=1.145000 Tap OK (diff=0.0050mm, stable 3/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (2/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (3/10) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (4/10) probe at 56.001,334.001 is z=1.142500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1425 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete! probe at 56.001,334.001 is z=495.782500 probe at 56.001,334.001 is z=486.107500 Tap drift (diff=9.6750mm) — reset probe at 56.001,334.001 is z=486.102500 probe at 56.001,334.001 is z=486.115000 Tap OK (diff=0.0075mm, stable 2/5) probe at 56.001,334.001 is z=486.117500 Tap drift (diff=0.0100mm) — reset probe at 56.001,334.001 is z=486.100000

probe: at 56.003,334.994 bed will contact at z=1.857500 probe: at 56.003,334.994 bed will contact at z=1.855000 probe: at 56.003,334.994 bed will contact at z=1.862500 probe: at 388.002,334.994 bed will contact at z=1.885000 probe: at 388.002,334.994 bed will contact at z=1.892500 probe: at 388.002,110.001 bed will contact at z=1.877500 probe: at 388.002,110.001 bed will contact at z=1.880000 probe: at 388.002,110.001 bed will contact at z=1.885000 probe: at 56.003,110.001 bed will contact at z=1.900000 probe: at 56.003,110.001 bed will contact at z=1.905000 probe: at 221.996,222.004 bed will contact at z=1.957500 probe: at 221.996,222.004 bed will contact at z=1.907500 probe: at 221.996,222.004 bed will contact at z=1.932500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=1.85750 front right screw : x=405.0, y=305.0, z=1.89250 : adjust CW 00:04 rear right screw : x=405.0, y=80.0, z=1.88000 : adjust CW 00:03 rear left screw : x=73.0, y=80.0, z=1.90000 : adjust CW 00:05 rear middle screw : x=239.0, y=192.0, z=1.93250 : adjust CW 00:09