[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4A0020000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=357.0091 gap=1.9909 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9847 gap=2.0153 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=357.0091 gap=1.9909 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=306.410000 probe at 65.996,275.995 is z=306.420000 Tap drift (diff=0.0100mm) — reset probe at 65.996,275.995 is z=306.425000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=306.722500 Tap drift (diff=0.2975mm) — reset probe at 65.996,275.995 is z=306.442500 Tap drift (diff=0.2800mm) — reset probe at 65.996,275.995 is z=306.430000 Tap drift (diff=0.0125mm) — reset probe at 65.996,275.995 is z=306.422500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.996,275.995 is z=306.427500 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 65.996,275.995 is z=306.432500 Tap OK (diff=0.0075mm, stable 5/5) VALIDATED: trigger_z=306.4325 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=355.262500 probe at 65.999,275.995 is z=358.177500 Tap drift (diff=2.9150mm) — reset probe at 65.999,275.995 is z=188.945000 Tap drift (diff=169.2325mm) — reset probe at 65.999,275.995 is z=178.912500 Tap drift (diff=10.0325mm) — reset probe at 65.999,275.995 is z=0.885000 Tap drift (diff=178.0275mm) — reset probe at 65.999,275.995 is z=0.905000 Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=0.910000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=0.900000 Tap OK (diff=0.0100mm, stable 3/5) probe at 65.999,275.995 is z=0.907500 Tap OK (diff=0.0075mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=0.9075 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.887500 probe at 65.999,275.995 is z=385.902500 Tap drift (diff=0.0150mm) — reset Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 65.999,275.995 is z=385.905000 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.999,275.995 is z=385.900000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=385.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=385.895000 probe at 65.999,275.995 is z=385.892500 Tap OK (diff=0.0100mm, stable 5/5) VALIDATED: trigger_z=385.8925 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=391.070000 Tap drift (diff=5.1750mm) — reset

probe: at 67.000,271.004 bed will contact at z=1.692500 probe: at 67.000,271.004 bed will contact at z=1.640000 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.645000 probe: at 67.000,271.004 bed will contact at z=1.702500 probe: at 67.000,271.004 bed will contact at z=1.722500 probe: at 67.000,271.004 bed will contact at z=1.682500 probe: at 67.000,271.004 bed will contact at z=1.650000 probe: at 67.000,271.004 bed will contact at z=1.752500 probe: at 67.000,271.004 bed will contact at z=1.732500 probe: at 67.000,271.004 bed will contact at z=1.635000 probe: at 67.000,271.004 bed will contact at z=1.675000 probe: at 67.000,271.004 bed will contact at z=1.655000 probe: at 67.000,271.004 bed will contact at z=1.707500 probe: at 67.000,271.004 bed will contact at z=1.622500 probe: at 67.000,271.004 bed will contact at z=1.715000 probe: at 67.000,271.004 bed will contact at z=1.680000 probe: at 67.000,271.004 bed will contact at z=1.667500 probe: at 67.000,271.004 bed will contact at z=1.625000 probe: at 67.000,271.004 bed will contact at z=1.660000 probe: at 67.000,271.004 bed will contact at z=1.665000 probe: at 267.996,271.004 bed will contact at z=1.740000 probe: at 267.996,71.995 bed will contact at z=1.620000 probe: at 267.996,71.995 bed will contact at z=1.615000 probe: at 267.996,71.995 bed will contact at z=1.617500 probe: at 67.000,71.995 bed will contact at z=1.660000 probe: at 67.000,71.995 bed will contact at z=1.615000 probe: at 67.000,71.995 bed will contact at z=1.667500 probe: at 67.000,71.995 bed will contact at z=1.637500 probe: at 67.000,71.995 bed will contact at z=1.662500 probe: at 67.000,71.995 bed will contact at z=1.632500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.66500 front right screw : x=285.0, y=241.0, z=1.74000 : adjust CW 00:09 rear right screw : x=285.0, y=42.0, z=1.61750 : adjust CCW 00:06 rear left screw : x=84.0, y=42.0, z=1.63750 : adjust CCW 00:03