[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=300;ssr=SSR10DA;lot=20260616;uid=61C229 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4B0022000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.3869 gap=1.6131 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.1828/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.0426 spread=0.1828mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-29.8141 gap=2.1859 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-30.1797 gap=1.8203 (2/4) tap 4: pos=-29.8141 gap=2.1859 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=175.977500 Tap OK (diff=0.0000mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=175.9775 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=265.535000 Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 30.994,211.998 is z=267.175000 Tap rejete (vibration chassis, z=267.1750 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 30.994,211.998 is z=266.615000 probe at 30.994,211.998 is z=269.175000 Tap rejete (vibration chassis, z=269.1750 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 30.994,211.998 is z=268.817500 Tap rejete (vibration chassis, z=268.8175 > max-z_hop) -> pas de remontee, on poursuit la descente (3) probe at 30.994,211.998 is z=268.335000 Tap rejete (vibration chassis, z=268.3350 > max-z_hop) -> pas de remontee, on poursuit la descente (4) probe at 30.994,211.998 is z=267.897500 Tap rejete (vibration chassis, z=267.8975 > max-z_hop) -> pas de remontee, on poursuit la descente (5) probe at 30.994,211.998 is z=267.415000 Tap rejete (vibration chassis, z=267.4150 > max-z_hop) -> pas de remontee, on poursuit la descente (6) probe at 30.994,211.998 is z=266.935000 probe at 30.994,211.998 is z=267.492500 Tap rejete (vibration chassis, z=267.4925 > max-z_hop) -> pas de remontee, on poursuit la descente (7) probe at 30.994,211.998 is z=267.137500 Tap rejete (vibration chassis, z=267.1375 > max-z_hop) -> pas de remontee, on poursuit la descente (8) probe at 30.994,211.998 is z=266.777500 probe at 30.994,211.998 is z=269.135000 Tap rejete (vibration chassis, z=269.1350 > max-z_hop) -> pas de remontee, on poursuit la descente (9) probe at 30.994,211.998 is z=268.015000 Tap rejete (vibration chassis, z=268.0150 > max-z_hop) -> pas de remontee, on poursuit la descente (10) probe at 30.994,211.998 is z=267.777500 Tap rejete (vibration chassis, z=267.7775 > max-z_hop) -> pas de remontee, on poursuit la descente (11) probe at 30.994,211.998 is z=266.825000 probe at 30.994,211.998 is z=269.377500 Tap rejete (vibration chassis, z=269.3775 > max-z_hop) -> pas de remontee, on poursuit la descente (12) probe at 30.994,211.998 is z=269.015000 Tap rejete (vibration chassis, z=269.0150 > max-z_hop) -> pas de remontee, on poursuit la descente (13) probe at 30.994,211.998 is z=268.860000 Tap rejete (vibration chassis, z=268.8600 > max-z_hop) -> pas de remontee, on poursuit la descente (14) probe at 30.994,211.998 is z=268.252500 Tap rejete (vibration chassis, z=268.2525 > max-z_hop) -> pas de remontee, on poursuit la descente (15) probe at 30.994,211.998 is z=267.695000 Tap rejete (vibration chassis, z=267.6950 > max-z_hop) -> pas de remontee, on poursuit la descente (16)

probe: at 32.495,205.497 bed will contact at z=1.145000 probe: at 32.495,205.497 bed will contact at z=1.142500 probe: at 32.495,205.497 bed will contact at z=1.182500 probe: at 206.996,205.497 bed will contact at z=3.930000 probe: at 206.996,205.497 bed will contact at z=3.932500 probe: at 206.996,205.497 bed will contact at z=3.935000 probe: at 206.996,31.995 bed will contact at z=5.255000 probe: at 206.996,31.995 bed will contact at z=5.262500 probe: at 206.996,31.995 bed will contact at z=5.265000 probe: at 32.495,31.995 bed will contact at z=2.570000 probe: at 32.495,31.995 bed will contact at z=2.550000 probe: at 32.495,31.995 bed will contact at z=2.567500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.14500 front right screw : x=224.0, y=175.5, z=3.93250 : adjust CW 05:35 rear right screw : x=224.0, y=2.0, z=5.26250 : adjust CW 08:14 rear left screw : x=49.5, y=2.0, z=2.56750 : adjust CW 02:51