[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4B0029000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=457.1919 gap=1.8081 (1/4) tap 3: pos=456.9847 gap=2.0153 (2/4) tap 4: pos=457.0091 gap=1.9909 (3/4) tap 5: pos=456.9847 gap=2.0153 fenetre=0.2072/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0426 spread=0.2072mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=453.8647 gap=5.1353 (chauffe, ignore) tap 2 rejete: cible atteinte sans buter (gap=0.0653) tap 3: pos=454.2791 gap=4.7209 (1/4) tap 4 rejete: cible atteinte sans buter (gap=0.0653) tap 5 rejete: cible atteinte sans buter (gap=0.8209) YUMI_SENSORLESS_HOME X: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 6: pos=457.2284 gap=1.7716 (2/4) tap 7: pos=456.9847 gap=2.0153 (3/4) tap 8: pos=456.8141 gap=2.1859 fenetre=2.9494/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (3 rejetes) -> moyenne=456.3266 spread=2.9494mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.5819 spread=0.7800mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=453.8647 gap=5.1353 (chauffe, ignore) tap 2: pos=456.2169 gap=2.7831 (1/4) tap 3 rejete: cible atteinte sans buter (gap=0.0653) tap 4 rejete: cible atteinte sans buter (gap=0.0531) YUMI_SENSORLESS_HOME X: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 5: pos=457.0334 gap=1.9666 (2/4) tap 6: pos=456.9969 gap=2.0031 (3/4) tap 7: pos=456.9969 gap=2.0031 fenetre=0.8166/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (2 rejetes) -> moyenne=456.8110 spread=0.8166mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-17.9969 gap=2.0031 (3/4) tap 5: pos=-17.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-17.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=413.495000 Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=413.500000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.995,339.999 is z=413.502500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=413.5025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=180.197500 probe at 49.998,339.999 is z=182.190000 Tap drift (diff=1.9925mm) — reset probe at 49.998,339.999 is z=107.362500 Tap drift (diff=74.8275mm) — reset probe at 49.998,339.999 is z=110.175000 Tap drift (diff=2.8125mm) — reset probe at 49.998,339.999 is z=95.570000 Tap drift (diff=14.6050mm) — reset probe at 49.998,339.999 is z=70.940000 Tap drift (diff=24.6300mm) — reset probe at 49.998,339.999 is z=70.405000 Tap drift (diff=0.5350mm) — reset probe at 49.998,339.999 is z=72.935000 Tap drift (diff=2.5300mm) — reset probe at 49.998,339.999 is z=75.730000 Tap drift (diff=2.7950mm) — reset probe at 49.998,339.999 is z=77.050000 Tap drift (diff=1.3200mm) — reset probe at 49.998,339.999 is z=1.107500 Tap drift (diff=75.9425mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=1.112500 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1125 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.107500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=486.105000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) VALIDATED: trigger_z=486.1075 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.102500 probe at 49.998,339.999 is z=486.097500

probe: at 54.997,328.001 bed will contact at z=1.025000 probe: at 54.997,328.001 bed will contact at z=1.030000 probe: at 380.001,328.001 bed will contact at z=1.042500 probe: at 380.001,328.001 bed will contact at z=1.085000 probe: at 380.001,328.001 bed will contact at z=1.087500 probe: at 380.001,101.996 bed will contact at z=1.005000 probe: at 380.001,101.996 bed will contact at z=1.075000 Probe samples exceed tolerance. Retrying... probe: at 380.001,101.996 bed will contact at z=1.057500 probe: at 380.001,101.996 bed will contact at z=1.032500 probe: at 380.001,101.996 bed will contact at z=1.022500 probe: at 54.997,101.996 bed will contact at z=1.012500 probe: at 54.997,101.996 bed will contact at z=1.010000 probe: at 54.997,101.996 bed will contact at z=1.015000 probe: at 217.505,214.498 bed will contact at z=1.050000 probe: at 217.505,214.498 bed will contact at z=1.085000 probe: at 217.505,214.498 bed will contact at z=1.082500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.02500 front right screw : x=397.0, y=298.0, z=1.08500 : adjust CW 00:07 rear right screw : x=397.0, y=72.0, z=1.03250 : adjust CW 00:01 rear left screw : x=72.0, y=72.0, z=1.01250 : adjust CCW 00:01 middle : x=234.5, y=184.5, z=1.08250 : adjust CW 00:07