[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4B0032000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=357.0091 gap=1.9909 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=304.307500 probe at 65.996,275.995 is z=304.347500 Tap drift (diff=0.0400mm) — reset probe at 65.996,275.995 is z=304.350000 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.996,275.995 is z=304.352500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=304.3525 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=385.750000 probe at 65.999,275.995 is z=285.867500 Tap drift (diff=99.8825mm) — reset probe at 65.999,275.995 is z=288.762500 Tap drift (diff=2.8950mm) — reset probe at 65.999,275.995 is z=281.417500 Tap drift (diff=7.3450mm) — reset probe at 65.999,275.995 is z=198.992500 Tap drift (diff=82.4250mm) — reset probe at 65.999,275.995 is z=189.112500 Tap drift (diff=9.8800mm) — reset probe at 65.999,275.995 is z=0.800000 Tap drift (diff=188.3125mm) — reset probe at 65.999,275.995 is z=0.855000 Tap drift (diff=0.0550mm) — reset probe at 65.999,275.995 is z=0.850000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=0.852500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=0.862500 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.867500 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.999,275.995 is z=0.865000 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.999,275.995 is z=0.860000 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=0.8600 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.890000 probe at 65.999,275.995 is z=385.905000 Tap drift (diff=0.0150mm) — reset probe at 65.999,275.995 is z=385.910000 probe at 65.999,275.995 is z=385.922500 Tap drift (diff=0.0125mm) — reset probe at 65.999,275.995 is z=385.930000 Tap OK (diff=0.0075mm, stable 2/5)

probe: at 67.000,271.004 bed will contact at z=0.937500 probe: at 67.000,271.004 bed will contact at z=0.957500 probe: at 67.000,271.004 bed will contact at z=0.962500 probe: at 267.996,271.004 bed will contact at z=1.020000 probe: at 267.996,271.004 bed will contact at z=1.022500 probe: at 267.996,271.004 bed will contact at z=1.027500 probe: at 267.996,71.995 bed will contact at z=1.097500 probe: at 267.996,71.995 bed will contact at z=1.100000 probe: at 267.996,71.995 bed will contact at z=1.105000 probe: at 67.000,71.995 bed will contact at z=1.010000 probe: at 67.000,71.995 bed will contact at z=1.030000 probe: at 67.000,71.995 bed will contact at z=1.017500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=0.95750 front right screw : x=285.0, y=241.0, z=1.02250 : adjust CW 00:08 rear right screw : x=285.0, y=42.0, z=1.10000 : adjust CW 00:17 rear left screw : x=84.0, y=42.0, z=1.01750 : adjust CW 00:07