[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=550;ssr=SSR10DA;lot=20260618;uid=2ACAAE [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4C004D000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=457.1797 gap=1.8203 (1/4) tap 3: pos=457.5941 gap=1.4059 (2/4) tap 4: pos=457.1797 gap=1.8203 (3/4) tap 5: pos=457.7769 gap=1.2231 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.4326 spread=0.5972mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-18.3869 gap=1.6131 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7647 gap=1.2353 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.6763 spread=0.3900mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.3869 gap=1.6131 (2/4) tap 4: pos=456.6069 gap=2.3931 (3/4) tap 5: pos=457.1919 gap=1.8081 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.7800mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-17.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-17.9969 gap=2.0031 (1/4) tap 3: pos=-18.3625 gap=1.6375 (2/4) tap 4: pos=-18.4112 gap=1.5888 (3/4) tap 5: pos=-18.3625 gap=1.6375 fenetre=0.4144/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.2833 spread=0.4144mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=457.3869 gap=1.6131 (2/4) tap 4: pos=456.6069 gap=2.3931 (3/4) tap 5: pos=457.1919 gap=1.8081 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=457.0456 spread=0.7800mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.6062 gap=1.3938 (chauffe, ignore) tap 2: pos=-18.7769 gap=1.2231 (1/4) tap 3: pos=-18.7769 gap=1.2231 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-18.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=403.935000 probe at 49.995,339.999 is z=403.947500 Tap drift (diff=0.0125mm) — reset probe at 49.995,339.999 is z=403.957500 Tap drift (diff=0.0100mm) — reset probe at 49.995,339.999 is z=403.960000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 49.995,339.999 is z=403.965000 Tap OK (diff=0.0050mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=403.9650 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=1.145000 probe at 49.998,339.999 is z=1.165000 Tap drift (diff=0.0200mm) — reset probe at 49.998,339.999 is z=1.167500 Tap OK (diff=0.0025mm, stable 2/5) probe at 49.998,339.999 is z=1.175000 Tap OK (diff=0.0075mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=1.1750 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=486.090000 probe at 49.998,339.999 is z=486.102500 Tap drift (diff=0.0125mm) — reset probe at 49.998,339.999 is z=486.100000 probe at 49.998,339.999 is z=486.105000 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=486.1050 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.087500 Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=486.097500 Tap OK (diff=0.0025mm, stable 3/5) VALIDATED: trigger_z=486.1000 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.092500 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,339.999 is z=486.095000 Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0050mm, stable 4/5) VALIDATED: trigger_z=486.1025 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) VALIDATED: trigger_z=486.0975 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) probe at 49.998,339.999 is z=486.115000 probe at 49.998,339.999 is z=488.330000 Tap drift (diff=2.2150mm) — reset Tap drift (diff=2.2325mm) — reset probe at 49.998,339.999 is z=489.060000

probe: at 54.997,328.001 bed will contact at z=2.112500 probe: at 54.997,328.001 bed will contact at z=2.122500 probe: at 54.997,328.001 bed will contact at z=2.125000 probe: at 380.001,328.001 bed will contact at z=2.117500 probe: at 380.001,328.001 bed will contact at z=2.202500 Probe samples exceed tolerance. Retrying... probe: at 380.001,328.001 bed will contact at z=2.210000 probe: at 380.001,328.001 bed will contact at z=2.207500 probe: at 380.001,101.996 bed will contact at z=2.040000 probe: at 380.001,101.996 bed will contact at z=2.025000 probe: at 54.997,101.996 bed will contact at z=2.040000 probe: at 54.997,101.996 bed will contact at z=2.052500 probe: at 54.997,101.996 bed will contact at z=2.055000 probe: at 217.505,214.498 bed will contact at z=2.107500 probe: at 217.505,214.498 bed will contact at z=2.115000 probe: at 217.505,214.498 bed will contact at z=2.090000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=2.12250 front right screw : x=397.0, y=298.0, z=2.21000 : adjust CW 00:11 rear right screw : x=397.0, y=72.0, z=2.04000 : adjust CCW 00:10 rear left screw : x=72.0, y=72.0, z=2.05250 : adjust CCW 00:08 middle : x=234.5, y=184.5, z=2.10750 : adjust CCW 00:02