[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4C005E000C51353234323830

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7525 gap=1.2475 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=357.0091 gap=1.9909 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0122/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9999 spread=0.0122mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=357.1797 gap=1.8203 (1/4) tap 3: pos=356.8141 gap=2.1859 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.5941 gap=1.4059 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 125mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.8019 gap=2.1981 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=357.1797 gap=1.8203 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3778/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9938 spread=0.3778mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=286.177500 probe at 65.996,275.995 is z=288.962500 Tap drift (diff=2.7850mm) — reset probe at 65.996,275.995 is z=286.207500 Tap drift (diff=2.7550mm) — reset probe at 65.996,275.995 is z=286.205000 Tap OK (diff=0.0025mm, stable 2/5) Tap drift (diff=0.0275mm) — reset probe at 65.996,275.995 is z=286.180000 probe at 65.996,275.995 is z=286.182500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=286.1800 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.620000 probe at 65.999,275.995 is z=375.967500 Tap drift (diff=19.6525mm) — reset probe at 65.999,275.995 is z=365.685000 Tap drift (diff=10.2825mm) — reset probe at 65.999,275.995 is z=7.305000 Tap drift (diff=358.3800mm) — reset probe at 65.999,275.995 is z=7.360000 Tap drift (diff=0.0550mm) — reset probe at 65.999,275.995 is z=7.362500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=7.365000 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=7.367500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=7.3675 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=386.862500 probe at 65.999,275.995 is z=385.902500 Tap drift (diff=0.9600mm) — reset probe at 65.999,275.995 is z=388.697500 Tap drift (diff=2.7950mm) — reset probe at 65.999,275.995 is z=391.652500 Tap drift (diff=2.9550mm) — reset probe at 65.999,275.995 is z=385.905000 Tap drift (diff=5.7475mm) — reset probe at 65.999,275.995 is z=386.342500 Tap drift (diff=0.4400mm) — reset Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) VALIDATED: trigger_z=385.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=395.815000 probe at 65.999,275.995 is z=394.700000 Tap drift (diff=1.1150mm) — reset probe at 65.999,275.995 is z=393.225000 Tap drift (diff=1.4750mm) — reset

probe: at 67.000,271.004 bed will contact at z=1.245000 probe: at 67.000,271.004 bed will contact at z=1.242500 probe: at 67.000,271.004 bed will contact at z=1.235000 probe: at 267.996,271.004 bed will contact at z=1.262500 probe: at 267.996,271.004 bed will contact at z=1.267500 probe: at 267.996,71.995 bed will contact at z=1.307500 probe: at 67.000,71.995 bed will contact at z=1.270000 probe: at 67.000,71.995 bed will contact at z=1.282500 probe: at 67.000,71.995 bed will contact at z=1.267500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.24250 front right screw : x=285.0, y=241.0, z=1.26750 : adjust CW 00:03 rear right screw : x=285.0, y=42.0, z=1.30750 : adjust CW 00:08 rear left screw : x=84.0, y=42.0, z=1.27000 : adjust CW 00:03