[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C235;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=300;ssr=SSR10DA;lot=20260618;uid=BBA413 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4C0065000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.9841 gap=1.0159 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=255.9847 gap=2.0153 (1/4) tap 3: pos=256.0091 gap=1.9909 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0244/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0244mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=256.9597 gap=1.0403 (chauffe, ignore) tap 2: pos=255.9969 gap=2.0031 (1/4) tap 3: pos=255.9969 gap=2.0031 (2/4) tap 4: pos=255.9969 gap=2.0031 (3/4) tap 5: pos=255.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=255.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=256.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 31.003,211.998 is z=265.740000 probe at 31.003,211.998 is z=265.780000 Tap drift (diff=0.0400mm) — reset probe at 31.003,211.998 is z=244.305000 Tap drift (diff=21.4750mm) — reset probe at 31.003,211.998 is z=153.507500 Tap drift (diff=90.7975mm) — reset probe at 31.003,211.998 is z=153.497500 Tap drift (diff=0.0100mm) — reset probe at 31.003,211.998 is z=153.472500 Tap drift (diff=0.0250mm) — reset probe at 31.003,211.998 is z=153.470000 Tap OK (diff=0.0025mm, stable 2/5) probe at 31.003,211.998 is z=153.467500 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=153.4675 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (31.0, 212.0) ~ point de tap (31.0, 212.0) Z calibration complete!

Moving to tap point X=31.0 Y=212.0... Probing with pressure switch... probe at 30.994,211.998 is z=265.812500 probe at 30.994,211.998 is z=268.495000 Tap rejete (vibration chassis, z=268.4950 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 30.994,211.998 is z=268.252500 Tap rejete (vibration chassis, z=268.2525 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 30.994,211.998 is z=268.015000 Tap rejete (vibration chassis, z=268.0150 > max-z_hop) -> pas de remontee, on poursuit la descente (3) probe at 30.994,211.998 is z=267.770000 Tap rejete (vibration chassis, z=267.7700 > max-z_hop) -> pas de remontee, on poursuit la descente (4) probe at 30.994,211.998 is z=267.570000 Tap rejete (vibration chassis, z=267.5700 > max-z_hop) -> pas de remontee, on poursuit la descente (5) probe at 30.994,211.998 is z=253.452500 probe at 30.994,211.998 is z=256.137500 Tap drift (diff=2.6850mm) — reset Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 30.994,211.998 is z=213.900000 Tap drift (diff=42.2375mm) — reset probe at 30.994,211.998 is z=159.345000 Tap drift (diff=54.5550mm) — reset probe at 30.994,211.998 is z=159.495000 Tap drift (diff=0.1500mm) — reset probe at 30.994,211.998 is z=5.012500 Tap drift (diff=154.4825mm) — reset probe at 30.994,211.998 is z=1.217500 Tap drift (diff=3.7950mm) — reset probe at 30.994,211.998 is z=1.215000 Tap OK (diff=0.0025mm, stable 2/5) Tap OK (diff=0.0000mm, stable 3/5) probe at 30.994,211.998 is z=3.972500 Tap drift (diff=2.7575mm) — reset probe at 30.994,211.998 is z=3.975000 Tap drift (diff=2.7600mm) — reset probe at 30.994,211.998 is z=1.212500 Tap drift (diff=2.7625mm) — reset probe at 30.994,211.998 is z=3.812500 Tap drift (diff=2.6000mm) — reset Tap drift (diff=2.5975mm) — reset probe at 30.994,211.998 is z=3.697500

probe: at 32.495,205.497 bed will contact at z=1.602500 probe: at 32.495,205.497 bed will contact at z=1.622500 probe: at 32.495,205.497 bed will contact at z=1.605000 probe: at 206.996,205.497 bed will contact at z=1.600000 probe: at 206.996,205.497 bed will contact at z=1.617500 probe: at 206.996,205.497 bed will contact at z=1.590000 probe: at 206.996,31.995 bed will contact at z=1.750000 probe: at 206.996,31.995 bed will contact at z=1.780000 probe: at 206.996,31.995 bed will contact at z=1.765000 probe: at 32.495,31.995 bed will contact at z=1.570000 probe: at 32.495,31.995 bed will contact at z=1.565000 probe: at 32.495,31.995 bed will contact at z=1.575000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=49.5, y=175.5, z=1.60500 front right screw : x=224.0, y=175.5, z=1.60000 : adjust CCW 00:01 rear right screw : x=224.0, y=2.0, z=1.76500 : adjust CW 00:19 rear left screw : x=49.5, y=2.0, z=1.57000 : adjust CCW 00:04