[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4C006A000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-21.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9847 gap=2.0153 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=467.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=466.9969 gap=2.0031 (1/4) tap 3: pos=466.9969 gap=2.0031 (2/4) tap 4: pos=466.9969 gap=2.0031 (3/4) tap 5: pos=466.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=466.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=467.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-20.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-20.9969 gap=2.0031 (1/4) tap 3: pos=-20.9969 gap=2.0031 (2/4) tap 4: pos=-20.9969 gap=2.0031 (3/4) tap 5: pos=-20.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-20.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-21.0000 Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 55.998,334.001 is z=495.572500 probe at 55.998,334.001 is z=498.287500 Tap rejete (vibration chassis, z=498.2875 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 55.998,334.001 is z=498.100000 Tap rejete (vibration chassis, z=498.1000 > max-z_hop) -> pas de remontee, on poursuit la descente (2) probe at 55.998,334.001 is z=497.725000 Tap rejete (vibration chassis, z=497.7250 > max-z_hop) -> pas de remontee, on poursuit la descente (3) probe at 55.998,334.001 is z=410.115000 Tap OK (diff=0.0000mm, stable 2/5) probe at 55.998,334.001 is z=410.120000 Tap OK (diff=0.0050mm, stable 3/5) probe at 55.998,334.001 is z=410.127500 Tap OK (diff=0.0075mm, stable 4/5) probe at 55.998,334.001 is z=410.122500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=410.1225 -> Z=0 pose -0.1000 au-dessus du tap (compression=0.0000 - z_offset=0.1000) Maillage OK (config): zero_reference_position (56.0, 334.0) ~ point de tap (56.0, 334.0) Z calibration complete!

Moving to tap point X=56.0 Y=334.0... Probing with pressure switch... probe at 56.001,334.001 is z=487.275000 probe at 56.001,334.001 is z=457.512500 Tap drift (diff=29.7625mm) — reset probe at 56.001,334.001 is z=460.220000 Tap drift (diff=2.7075mm) — reset probe at 56.001,334.001 is z=462.940000 Tap drift (diff=2.7200mm) — reset probe at 56.001,334.001 is z=465.472500 Tap drift (diff=2.5325mm) — reset probe at 56.001,334.001 is z=468.185000 Tap drift (diff=2.7125mm) — reset probe at 56.001,334.001 is z=470.910000 Tap drift (diff=2.7250mm) — reset probe at 56.001,334.001 is z=421.460000 Tap drift (diff=49.4500mm) — reset probe at 56.001,334.001 is z=424.375000 Tap drift (diff=2.9150mm) — reset probe at 56.001,334.001 is z=427.075000 Tap drift (diff=2.7000mm) — reset probe at 56.001,334.001 is z=429.815000 Tap drift (diff=2.7400mm) — reset probe at 56.001,334.001 is z=400.597500 Tap drift (diff=29.2175mm) — reset probe at 56.001,334.001 is z=403.342500 Tap drift (diff=2.7450mm) — reset probe at 56.001,334.001 is z=406.097500 Tap drift (diff=2.7550mm) — reset probe at 56.001,334.001 is z=409.087500 Tap drift (diff=2.9900mm) — reset probe at 56.001,334.001 is z=411.825000 Tap drift (diff=2.7375mm) — reset probe at 56.001,334.001 is z=414.555000 Tap drift (diff=2.7300mm) — reset probe at 56.001,334.001 is z=417.270000 Tap drift (diff=2.7150mm) — reset probe at 56.001,334.001 is z=419.835000 Tap drift (diff=2.5650mm) — reset probe at 56.001,334.001 is z=422.542500

probe: at 56.003,334.994 bed will contact at z=2.542500 probe: at 56.003,334.994 bed will contact at z=2.545000 probe: at 388.002,334.994 bed will contact at z=2.570000 probe: at 388.002,334.994 bed will contact at z=2.555000 probe: at 388.002,334.994 bed will contact at z=2.565000 probe: at 388.002,110.001 bed will contact at z=2.502500 probe: at 388.002,110.001 bed will contact at z=2.512500 probe: at 388.002,110.001 bed will contact at z=2.492500 probe: at 56.003,110.001 bed will contact at z=2.522500 probe: at 56.003,110.001 bed will contact at z=2.527500 probe: at 56.003,110.001 bed will contact at z=2.520000 probe: at 221.996,222.004 bed will contact at z=2.502500 probe: at 221.996,222.004 bed will contact at z=2.495000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=73.0, y=305.0, z=2.54250 front right screw : x=405.0, y=305.0, z=2.56500 : adjust CW 00:03 rear right screw : x=405.0, y=80.0, z=2.50250 : adjust CCW 00:05 rear left screw : x=73.0, y=80.0, z=2.52250 : adjust CCW 00:02 rear middle screw : x=239.0, y=192.0, z=2.50250 : adjust CCW 00:05