[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4C0074000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.5941 gap=1.4059 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.5972/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.1462 spread=0.5972mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7769 gap=1.2231 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.782500 probe at 65.996,275.995 is z=398.575000 Tap rejete (vibration chassis, z=398.5750 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 65.996,275.995 is z=313.470000 probe at 65.996,275.995 is z=313.485000 Tap drift (diff=0.0150mm) — reset probe at 65.996,275.995 is z=313.490000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=313.492500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=313.495000 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.996,275.995 is z=313.497500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=313.4975 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=79.322500 probe at 65.999,275.995 is z=82.130000 Tap drift (diff=2.8075mm) — reset probe at 65.999,275.995 is z=84.907500 Tap drift (diff=2.7775mm) — reset probe at 65.999,275.995 is z=87.705000 Tap drift (diff=2.7975mm) — reset probe at 65.999,275.995 is z=90.497500 Tap drift (diff=2.7925mm) — reset probe at 65.999,275.995 is z=93.295000 probe at 65.999,275.995 is z=96.090000 Tap drift (diff=2.7950mm) — reset probe at 65.999,275.995 is z=98.530000 Tap drift (diff=2.4400mm) — reset probe at 65.999,275.995 is z=101.292500 Tap drift (diff=2.7625mm) — reset probe at 65.999,275.995 is z=104.067500 Tap drift (diff=2.7750mm) — reset probe at 65.999,275.995 is z=106.857500 Tap drift (diff=2.7900mm) — reset probe at 65.999,275.995 is z=109.647500 probe at 65.999,275.995 is z=112.642500 Tap drift (diff=2.9950mm) — reset probe at 65.999,275.995 is z=114.205000 Tap drift (diff=1.5625mm) — reset probe at 65.999,275.995 is z=116.447500 Tap drift (diff=2.2425mm) — reset probe at 65.999,275.995 is z=118.867500 Tap drift (diff=2.4200mm) — reset probe at 65.999,275.995 is z=0.900000 Tap drift (diff=117.9675mm) — reset probe at 65.999,275.995 is z=0.920000 Tap drift (diff=0.0200mm) — reset probe at 65.999,275.995 is z=0.930000 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.932500 Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=0.935000

probe: at 67.000,271.004 bed will contact at z=1.365000 probe: at 67.000,271.004 bed will contact at z=1.372500 probe: at 67.000,271.004 bed will contact at z=1.362500 probe: at 267.996,271.004 bed will contact at z=1.422500 probe: at 267.996,271.004 bed will contact at z=1.382500 probe: at 267.996,271.004 bed will contact at z=1.392500 probe: at 267.996,71.995 bed will contact at z=1.402500 probe: at 267.996,71.995 bed will contact at z=1.390000 probe: at 267.996,71.995 bed will contact at z=1.395000 probe: at 67.000,71.995 bed will contact at z=1.347500 probe: at 67.000,71.995 bed will contact at z=1.327500 probe: at 67.000,71.995 bed will contact at z=1.340000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.36500 front right screw : x=285.0, y=241.0, z=1.39250 : adjust CW 00:03 rear right screw : x=285.0, y=42.0, z=1.39500 : adjust CW 00:04 rear left screw : x=84.0, y=42.0, z=1.34000 : adjust CCW 00:03