[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C435;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22S148H;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=750;ssr=SSR10DA;lot=20260618;uid=9221AF [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4D0025000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.4112 gap=1.5888 (chauffe, ignore) tap 2: pos=-18.3869 gap=1.6131 (1/4) tap 3: pos=-18.7647 gap=1.2353 (2/4) tap 4: pos=-18.7769 gap=1.2231 (3/4) tap 5: pos=-18.3991 gap=1.6009 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.5819 spread=0.3900mm (tol=0.0500). Zero pose en butee=-18.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=457.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=456.9969 gap=2.0031 (1/4) tap 3: pos=456.9969 gap=2.0031 (2/4) tap 4: pos=456.9969 gap=2.0031 (3/4) tap 5: pos=456.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=456.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3747 gap=1.6253 (chauffe, ignore) tap 2: pos=-18.3991 gap=1.6009 (1/4) tap 3: pos=-17.9969 gap=2.0031 (2/4) tap 4: pos=-18.3747 gap=1.6253 (3/4) tap 5: pos=-18.3991 gap=1.6009 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.2924 spread=0.4022mm (tol=0.0500). Zero pose en butee=-18.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 100mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1 rejete: cible atteinte sans buter (gap=0.0531) tap 2 rejete: cible atteinte sans buter (gap=0.0531) YUMI_SENSORLESS_HOME X: home de base suspect (pas de contact) -> re-home de recuperation 1/2 tap 3: pos=457.5697 gap=1.4303 (chauffe, ignore) tap 4: pos=457.1919 gap=1.8081 (1/4) tap 5: pos=456.8019 gap=2.1981 (2/4) tap 6: pos=457.1919 gap=1.8081 (3/4) tap 7: pos=456.9969 gap=2.0031 fenetre=0.3900/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (2 rejetes) -> moyenne=457.0456 spread=0.3900mm (tol=0.0500). Zero pose en butee=457.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-18.3991 gap=1.6009 (chauffe, ignore) tap 2: pos=-18.3747 gap=1.6253 (1/4) tap 3: pos=-18.3991 gap=1.6009 (2/4) tap 4: pos=-18.3747 gap=1.6253 (3/4) tap 5: pos=-18.7769 gap=1.2231 fenetre=0.4022/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-18.4813 spread=0.4022mm (tol=0.0500). Zero pose en butee=-18.0000 Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.995,339.999 is z=484.990000 probe at 49.995,339.999 is z=386.180000 Tap drift (diff=98.8100mm) — reset probe at 49.995,339.999 is z=386.207500 Tap drift (diff=0.0275mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.995,339.999 is z=386.210000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.995,339.999 is z=386.212500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=386.2125 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete!

Moving to tap point X=50.0 Y=340.0... Probing with pressure switch... probe at 49.998,339.999 is z=0.847500 probe at 49.998,339.999 is z=0.895000 Tap drift (diff=0.0475mm) — reset probe at 49.998,339.999 is z=0.902500 Tap OK (diff=0.0075mm, stable 2/5) probe at 49.998,339.999 is z=0.905000 Tap OK (diff=0.0025mm, stable 3/5) probe at 49.998,339.999 is z=0.907500 Tap OK (diff=0.0025mm, stable 4/5) probe at 49.998,339.999 is z=0.910000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.9100 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (50.0, 340.0) ~ point de tap (50.0, 340.0) Z calibration complete! probe at 49.998,339.999 is z=485.895000 probe at 49.998,339.999 is z=485.905000 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 49.998,339.999 is z=485.907500 Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=485.9050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 49.998,339.999 is z=485.900000 Tap OK (diff=0.0050mm, stable 2/5) probe at 49.998,339.999 is z=485.902500 VALIDATED: trigger_z=485.9025 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 49.998,339.999 is z=485.897500 VALIDATED: trigger_z=485.9000 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0075mm, stable 5/5) probe at 49.998,339.999 is z=495.782500 probe at 49.998,339.999 is z=497.412500 Tap rejete (vibration chassis, z=497.4125 > max-z_hop) -> pas de remontee, on poursuit la descente (1) probe at 49.998,339.999 is z=485.890000 Tap OK (diff=0.0050mm, stable 5/5) probe at 49.998,339.999 is z=485.910000 probe at 49.998,339.999 is z=485.927500

probe: at 54.997,328.001 bed will contact at z=1.537500 probe: at 54.997,328.001 bed will contact at z=1.545000 probe: at 54.997,328.001 bed will contact at z=1.542500 probe: at 380.001,328.001 bed will contact at z=1.600000 probe: at 380.001,328.001 bed will contact at z=1.610000 probe: at 380.001,328.001 bed will contact at z=1.595000 probe: at 380.001,101.996 bed will contact at z=1.542500 probe: at 380.001,101.996 bed will contact at z=1.537500 probe: at 380.001,101.996 bed will contact at z=1.547500 probe: at 54.997,101.996 bed will contact at z=1.580000 probe: at 54.997,101.996 bed will contact at z=1.585000 probe: at 54.997,101.996 bed will contact at z=1.590000 probe: at 217.505,214.498 bed will contact at z=1.525000 probe: at 217.505,214.498 bed will contact at z=1.522500 probe: at 217.505,214.498 bed will contact at z=1.550000 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=72.0, y=298.0, z=1.54250 front right screw : x=397.0, y=298.0, z=1.60000 : adjust CW 00:07 rear right screw : x=397.0, y=72.0, z=1.54250 : adjust CCW 00:00 rear left screw : x=72.0, y=72.0, z=1.58500 : adjust CW 00:05 middle : x=234.5, y=184.5, z=1.52500 : adjust CCW 00:02