[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=220V;bedw=500;ssr=SSR10DA;lot=20260618;uid=36C6E9 [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4D0029000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.2163 gap=1.7837 (chauffe, ignore) tap 2: pos=357.1919 gap=1.8081 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.1950/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=357.0456 spread=0.1950mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.0091 gap=1.9909 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5819 gap=1.4181 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=357.1797 gap=1.8203 (2/4) tap 4: pos=356.8141 gap=2.1859 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.3656/0.0500 YUMI_SENSORLESS_HOME X IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.3656mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 75mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.5697 gap=1.4303 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-29.9969 gap=2.0031 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-29.9969 gap=2.0031 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-29.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=309.807500 probe at 65.996,275.995 is z=309.812500 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=309.815000 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.996,275.995 is z=309.817500 Tap OK (diff=0.0025mm, stable 4/5) Tap OK (diff=0.0000mm, stable 5/5) VALIDATED: trigger_z=309.8175 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete!

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=395.977500 probe at 65.999,275.995 is z=315.407500 Tap drift (diff=80.5700mm) — reset probe at 65.999,275.995 is z=308.207500 Tap drift (diff=7.2000mm) — reset probe at 65.999,275.995 is z=300.207500 Tap drift (diff=8.0000mm) — reset probe at 65.999,275.995 is z=292.610000 Tap drift (diff=7.5975mm) — reset probe at 65.999,275.995 is z=285.240000 Tap drift (diff=7.3700mm) — reset probe at 65.999,275.995 is z=0.887500 Tap drift (diff=284.3525mm) — reset probe at 65.999,275.995 is z=0.897500 Tap drift (diff=0.0100mm) — reset Tap OK (diff=0.0000mm, stable 2/5) probe at 65.999,275.995 is z=0.895000 Tap OK (diff=0.0025mm, stable 3/5) Tap OK (diff=0.0025mm, stable 4/5) probe at 65.999,275.995 is z=0.902500 Tap OK (diff=0.0050mm, stable 5/5) VALIDATED: trigger_z=0.9025 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.900000 probe at 65.999,275.995 is z=387.782500 Tap drift (diff=1.8825mm) — reset probe at 65.999,275.995 is z=385.895000 Tap OK (diff=0.0050mm, stable 2/5) Switch encore declenche (vibration) -> attente 2.0s puis nouvelle tentative (1/10) probe at 65.999,275.995 is z=385.905000 probe at 65.999,275.995 is z=385.910000 Tap OK (diff=0.0000mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.999,275.995 is z=385.912500 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=385.9125 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.902500

probe: at 67.000,271.004 bed will contact at z=1.430000 probe: at 67.000,271.004 bed will contact at z=1.367500 Probe samples exceed tolerance. Retrying... probe: at 67.000,271.004 bed will contact at z=1.452500 probe: at 67.000,271.004 bed will contact at z=1.467500 probe: at 67.000,271.004 bed will contact at z=1.397500 probe: at 67.000,271.004 bed will contact at z=1.450000 probe: at 67.000,271.004 bed will contact at z=1.445000 probe: at 67.000,271.004 bed will contact at z=1.465000 probe: at 267.996,271.004 bed will contact at z=1.327500 probe: at 267.996,271.004 bed will contact at z=1.315000 probe: at 267.996,271.004 bed will contact at z=1.325000 probe: at 267.996,71.995 bed will contact at z=1.335000 probe: at 267.996,71.995 bed will contact at z=1.365000 probe: at 267.996,71.995 bed will contact at z=1.345000 probe: at 67.000,71.995 bed will contact at z=1.362500 probe: at 67.000,71.995 bed will contact at z=1.385000 probe: at 67.000,71.995 bed will contact at z=1.322500 probe: at 67.000,71.995 bed will contact at z=1.407500 probe: at 67.000,71.995 bed will contact at z=1.370000 probe: at 67.000,71.995 bed will contact at z=1.425000 probe: at 67.000,71.995 bed will contact at z=1.382500 probe: at 67.000,71.995 bed will contact at z=1.355000 probe: at 67.000,71.995 bed will contact at z=1.405000 probe: at 67.000,71.995 bed will contact at z=1.335000 probe: at 67.000,71.995 bed will contact at z=1.392500 probe: at 67.000,71.995 bed will contact at z=1.387500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.45000 front right screw : x=285.0, y=241.0, z=1.32500 : adjust CCW 00:15 rear right screw : x=285.0, y=42.0, z=1.34500 : adjust CCW 00:13 rear left screw : x=84.0, y=42.0, z=1.38750 : adjust CCW 00:07