[mcu] version: 5ac7c301 [mcu] board=SMART_MAKER_1_X;cpu=STM32F401;conn=UART;device=C335;x=SMART_TMC2209_V2;y=SMART_TMC2209_V2;z=SMART_TMC2209_V2;e0=SMART_TMC2209_V2;e1=SMART_TMC2209_V2;mx=42BYGH3023-B-22DH;my=42BYGH3023-B-22DH;mz=42BYGH2216-B-24DH;piezo=YN15T-85A1-W100_15-2P;pzb=Smart_Z-Offset;pzbv=0.2;mains=110V;bedw=500;ssr=SSR10DA;lot=20260618;uid=B3D7BD [mcu] comment: - [mcu SmartPiOne] version: 5ac7c301 (host SmartPi One) MCU_UID=4D003D000F51353135323934

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1797 gap=1.8203 (chauffe, ignore) tap 2: pos=-30.7769 gap=1.2231 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.7769 gap=1.2231 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME Y OK: 4 taps valides (0 rejetes) -> moyenne=-30.7769 spread=0.0000mm (tol=0.0500). Zero pose en butee=-30.0000

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-29.9969 gap=2.0031 (chauffe, ignore) tap 2: pos=-30.1919 gap=1.8081 (1/4) tap 3: pos=-30.7769 gap=1.2231 (2/4) tap 4: pos=-30.5819 gap=1.4181 (3/4) tap 5: pos=-29.9969 gap=2.0031 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000 Extruder 'extruder1' now syncing with '' Extruder 'extruder0' now syncing with 'extruder' QC CUTTER: motion sensor YMS-1 a change d'etat (mouvement detecte) QC CUTTER: extrude 60 + refroidit poop 5s + coupe + retracte 120 Extruder 'extruder0' now syncing with ''

Extruder 'extruder0' now syncing with '' Extruder 'extruder1' now syncing with '' Extruder 'extruder1' now syncing with 'extruder' QC E1_HEAD: motion sensor YMS-2 a change d'etat (mouvement detecte) QC E1_HEAD: filament a la tete apres 50mm + motion sensor YMS-2 OK

Run Current: 0.55A Hold Current: 0.55A YUMI_SENSORLESS_HOME X: home base... Run Current: 1.20A Hold Current: 1.09A tap 1: pos=357.7647 gap=1.2353 (chauffe, ignore) tap 2: pos=356.9969 gap=2.0031 (1/4) tap 3: pos=356.9969 gap=2.0031 (2/4) tap 4: pos=356.9969 gap=2.0031 (3/4) tap 5: pos=356.9969 gap=2.0031 fenetre=0.0000/0.0500 YUMI_SENSORLESS_HOME X OK: 4 taps valides (0 rejetes) -> moyenne=356.9969 spread=0.0000mm (tol=0.0500). Zero pose en butee=357.0000 YUMI_SENSORLESS_HOME Y: home base... Run Current: 1.20A Hold Current: 1.20A tap 1: pos=-30.1919 gap=1.8081 (chauffe, ignore) tap 2: pos=-30.5819 gap=1.4181 (1/4) tap 3: pos=-29.9969 gap=2.0031 (2/4) tap 4: pos=-30.1919 gap=1.8081 (3/4) tap 5: pos=-30.7769 gap=1.2231 fenetre=0.7800/0.0500 YUMI_SENSORLESS_HOME Y IMPRECIS: 4 taps valides (0 rejetes) -> moyenne=-30.3869 spread=0.7800mm (tol=0.0500). Zero pose en butee=-30.0000 Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.996,275.995 is z=395.600000 probe at 65.996,275.995 is z=354.320000 Tap drift (diff=41.2800mm) — reset probe at 65.996,275.995 is z=294.915000 Tap drift (diff=59.4050mm) — reset probe at 65.996,275.995 is z=285.962500 Tap drift (diff=8.9525mm) — reset probe at 65.996,275.995 is z=285.967500 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.996,275.995 is z=285.975000 Tap OK (diff=0.0075mm, stable 3/5) probe at 65.996,275.995 is z=285.990000 Tap drift (diff=0.0150mm) — reset probe at 65.996,275.995 is z=285.995000 probe at 65.996,275.995 is z=286.000000 Tap OK (diff=0.0050mm, stable 3/5) probe at 65.996,275.995 is z=286.007500 Tap OK (diff=0.0075mm, stable 4/5) probe at 65.996,275.995 is z=286.005000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=286.0050 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000)

Moving to tap point X=66.0 Y=276.0... Probing with pressure switch... probe at 65.999,275.995 is z=0.837500 probe at 65.999,275.995 is z=0.885000 Tap drift (diff=0.0475mm) — reset probe at 65.999,275.995 is z=0.895000 Tap drift (diff=0.0100mm) — reset probe at 65.999,275.995 is z=0.900000 Tap OK (diff=0.0050mm, stable 2/5) probe at 65.999,275.995 is z=0.902500 Tap OK (diff=0.0025mm, stable 3/5) probe at 65.999,275.995 is z=0.925000 Tap drift (diff=0.0225mm) — reset probe at 65.999,275.995 is z=0.932500 Tap OK (diff=0.0075mm, stable 2/5) probe at 65.999,275.995 is z=0.937500 Tap OK (diff=0.0050mm, stable 3/5) Tap OK (diff=0.0000mm, stable 4/5) probe at 65.999,275.995 is z=0.940000 Tap OK (diff=0.0025mm, stable 5/5) VALIDATED: trigger_z=0.9400 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) Maillage OK (config): zero_reference_position (66.0, 276.0) ~ point de tap (66.0, 276.0) Z calibration complete! probe at 65.999,275.995 is z=385.900000 probe at 65.999,275.995 is z=385.925000 Tap drift (diff=0.0250mm) — reset probe at 65.999,275.995 is z=385.932500 probe at 65.999,275.995 is z=385.935000 probe at 65.999,275.995 is z=385.937500 Tap OK (diff=0.0025mm, stable 4/5) probe at 65.999,275.995 is z=385.940000 VALIDATED: trigger_z=385.9400 -> Z=0 pose 0.1000 au-dessus du tap (compression=0.0000 + z_offset=0.1000) probe at 65.999,275.995 is z=385.885000 probe at 65.999,275.995 is z=385.897500 Tap drift (diff=0.0125mm) — reset Tap OK (diff=0.0025mm, stable 2/5) probe at 65.999,275.995 is z=385.905000 probe at 65.999,275.995 is z=385.922500 Tap drift (diff=0.0175mm) — reset probe at 65.999,275.995 is z=386.180000

probe: at 67.000,271.004 bed will contact at z=1.572500 probe: at 67.000,271.004 bed will contact at z=1.602500 probe: at 67.000,271.004 bed will contact at z=1.600000 probe: at 267.996,271.004 bed will contact at z=1.522500 probe: at 267.996,271.004 bed will contact at z=1.525000 probe: at 267.996,271.004 bed will contact at z=1.537500 probe: at 267.996,71.995 bed will contact at z=1.587500 probe: at 267.996,71.995 bed will contact at z=1.592500 probe: at 267.996,71.995 bed will contact at z=1.595000 probe: at 67.000,71.995 bed will contact at z=1.477500 probe: at 67.000,71.995 bed will contact at z=1.490000 probe: at 67.000,71.995 bed will contact at z=1.497500 01:20 means 1 full turn and 20 minutes, CW=clockwise, CCW=counter-clockwise front left screw (base) : x=84.0, y=241.0, z=1.60000 front right screw : x=285.0, y=241.0, z=1.52500 : adjust CCW 00:09 rear right screw : x=285.0, y=42.0, z=1.59250 : adjust CCW 00:01 rear left screw : x=84.0, y=42.0, z=1.49000 : adjust CCW 00:13